FeatherHAB/wsprhab Changeset - 38f0f2457409

Changeset - 38f0f2457409

Parent rev.

Child rev.

[Not reviewed]

default

0 3 0

Ethan Zonca - 9 years ago 2016-10-13 20:21:04
ez@ethanzonca.com

Fix issue where code would constantly enter gpsacq state because of last wspr timeout expiring

3 files changed with 18 insertions and 0 deletions:

src/gps.c

src/main.c

src/uart.c

0 comments (0 inline, 0 general)

src/gps.c

➞

Show inline comments

@@ @@ -225,24 +225,38 @@ void gps_poweron(void) @@
     // Begin DMA reception
     //HAL_UART_Receive_DMA(uart_gethandle(), nmeaBuffer, NMEABUFFER_SIZE);
     gpson = 1;
+}
 // Power off GPS module
 void gps_poweroff(void)
+{
     // NOTE: pchannel
 	position.hour = 0;
 	position.minute = 0;
 	position.second = 0;
 	position.altitude = 0;
 	position.latitude = 0;
 	position.longitude = 0;
 	position.day = 0;
 	position.month = 0;
 	position.fixtype = 0;
 	position.valid = 0;
 	position.pdop = 0;
 	position.sats_in_solution = 0;
 	position.speed = 0;
     uart_deinit();
     HAL_GPIO_WritePin(GPS_NOTEN, 1);
     gpson = 0;
+}
 gps_data_t* gps_getdata(void)
+{
     return &position;
+}
 uint8_t gps_ison(void)
+{

src/main.c

➞

Show inline comments

@@ @@ -131,24 +131,26 @@ int main(void) @@
                     // TODO: Set RTC for countdown to next transmission timeslot!
                     // TODO: Set wspr countdown timer for this transmission!
                     fix_acq_starttime = 0;
                     state = SYSTEM_WSPRTX;
+                }
                 // If no decent fix in 3 minutes
                 else if(HAL_GetTick() - fix_acq_starttime > 60000 * 3)
+                {
                 	// Flash error code and go to idle, try again next time
                 	led_blink(4);
                     gps_poweroff();
                     fix_acq_starttime = 0;
                     last_wspr_tx_time = HAL_GetTick(); // repeat acq/tx cycle after big time delay
                 	state = SYSTEM_IDLE;
+                }
             } break;
             // Wait for wspr timeslot and start transmitting
             case SYSTEM_WSPRTX:
+            {
             	blink_rate = BLINK_SLOW;
                 // Wait for wspr countdown timer to expire and go to tx
 //                if(timeout_expired)
 //                {

src/uart.c

➞

Show inline comments

@@ @@ -84,24 +84,26 @@ void uart_init(void) @@
     HAL_NVIC_DisableIRQ(USART1_IRQn);
     uart_initted = 1;
+}
 void uart_deinit(void)
+{
     if(uart_initted == 1)
+    {
         //HAL_DMA_DeInit(&hdma_usart1_rx);
         //HAL_DMA_DeInit(&hdma_usart1_tx);
         HAL_UART_DeInit(&huart1);
         __HAL_RCC_USART1_CLK_DISABLE();
         uart_initted = 0;
+    }
+}
 UART_HandleTypeDef* uart_gethandle(void)
+{
     return &huart1;
+}
 DMA_HandleTypeDef* uart_get_txdma_handle(void)
+{
     return &hdma_usart1_tx;

0 comments (0 inline, 0 general)