/*

 * Master Firmware: Configuration

 *

 * Wireless Observational Modular Aerial Network

 * 

 * Ethan Zonca

 * Matthew Kanning

 * Kyle Ripperger

 * Matthew Kroening

 *

 */

#ifndef CONFIG_H_

#define CONFIG_H_

#include <avr/pgmspace.h>

// --------------------------------------------------------------------------

// Hardware settings

// --------------------------------------------------------------------------

#define F_CPU 11059200

#define BOARDTEMP_ADDR 0x90

// --------------------------------------------------------------------------

// Module config (master.c)

// --------------------------------------------------------------------------

// Debug Output

//#define DEBUG_OUTPUT

// Blackout (turn off all but power LEDs)

#define BLACKOUT_ENABLE

#define BLACKOUT_TIMEOUT 1200000 // Blackout after 20 minutes (hopefully after fix and launch)

// Board heater setpoint

#define HEATER_THRESHOLD 5 // Regulate to 5 degrees Celsius

// Touchdown buzzer

#define BUZZER_RATE 5000

#define BUZZER_DURATION 1000

// --------------------------------------------------------------------------

// Error Codes config (logger.c)

// --------------------------------------------------------------------------

// SD Card

#define ERROR_SLAVETIMEOUT 0

#define ERROR_SD_INIT 1

#define ERROR_SD_PARTITION 2

#define ERROR_SD_FILE 3

#define ERROR_XBEETIMEOUT 4

#define ERROR_FATAL 5

#define ERROR_ATFAIL 6

#define ERROR_EXITAT 7

#define ERROR_INFOTEXT 8

#define ERROR_WATCHDOG 9

// !!! Please specify/update detailed messages for these error codes in logger.c

// --------------------------------------------------------------------------

// Slave Sensors config (slavesensors.c)

// --------------------------------------------------------------------------

// Slave data structure size

#define MAX_NUM_SLAVES 5	// Maximum number of nodes in the system

#define MAX_NUM_SENSORS 10	// Maximum number of unique types of sensors in the system

// Node identifier of log destination xbee

#define XBEE_LOGDEST_NAME "HAB-LOGGER"

// Rate to request data from slaves. Must be greater than AT delay * number slaves

#define DATAREQUEST_RATE 3000

// Timeouts

#define TIMEOUT_SLAVEREQUEST 500

#define TIMEOUT_NETWORKSCAN 7000

#define TIMEOUT_EXITAT 2000

#define TIMEOUT_XBEERESPONSE 2000

// Slave data request max retries (for retry upon corrupt data reception)

#define MAX_SLAVEREQUEST_RETRIES 2

// --------------------------------------------------------------------------

// Command Parser config (serparser.c)

// --------------------------------------------------------------------------

// Maximum payload size of command

#define MAX_PAYLOAD_LEN 16

// Circular serial buffer size. Must be at least MAX_CMD_LEN + 5

#define BUFFER_SIZE 128 

// --------------------------------------------------------------------------

// GPS config (xxx.c)

// --------------------------------------------------------------------------

// NMEA circular buffer size. Must be large enough to hold all received sentences

#define NMEABUFFER_SIZE 150

// --------------------------------------------------------------------------

// USART config (serial.c)

// --------------------------------------------------------------------------

// Baud rates for XBEE and GPS serial ports

#define USART0_BAUDRATE 115200

#define USART1_BAUDRATE 115200

// --------------------------------------------------------------------------

// AX.25 config (ax25.c)

// --------------------------------------------------------------------------

// TX delay in milliseconds

#define TX_DELAY      200

// Maximum packet delay

#define MAX_PACKET_LEN 512  // bytes

// --------------------------------------------------------------------------

// APRS config (aprs.c)

// --------------------------------------------------------------------------

// Set your callsign and SSID here. Common values for the SSID are

// (from http://zlhams.wikidot.com/aprs-ssidguide):

//

// - Balloons:  11

// - Cars:       9

// - Home:       0

// - IGate:      5

#define S_CALLSIGN      "KD8TDF"

#define S_CALLSIGN_ID   11

// Destination callsign: APRS (with SSID=0) is usually okay.