#define ERROR_NOXBEE 6

#define ERROR_CRAP 15

#define ERROR_ATFAIL 3

#define ERROR_EXITAT 8

// --------------------------------------------------------------------------

// Slave Sensors config (slavesensors.c)

// --------------------------------------------------------------------------

#define MAX_NUM_SLAVES 5  // Maximum number of nodes in the system

// Node identifier of log destination xbee

#define XBEE_LOGDEST_NAME "HAB-LOGGER"

#define DATAREQUEST_RATE 3000

// --------------------------------------------------------------------------

// Command Parser config (serparser.c)

// --------------------------------------------------------------------------

// Maximum payload size of command

#define MAX_PAYLOAD_LEN 16

#define S_CALLSIGN_ID   9 // 11

// Destination callsign: APRS (with SSID=0) is usually okay.

#define D_CALLSIGN      "APRS"

#define D_CALLSIGN_ID   0

// Digipeating paths:

// (read more about digipeating paths here: http://wa8lmf.net/DigiPaths/ )

// The recommended digi path for a balloon is WIDE2-1 or pathless. The default

// is pathless. Uncomment the following two lines for WIDE2-1 path:

#define DIGI_PATH1      "WIDE2"

#define DIGI_PATH1_TTL  1

// Transmit the APRS sentence every X milliseconds

#define APRS_TRANSMIT_PERIOD 20000

// --------------------------------------------------------------------------

// Logger config (logger.c)

// --------------------------------------------------------------------------

#define LOGGER_ID_EEPROM_ADDR 0x10

// Written to the beginning of every log file

 * Kyle Ripperger

 * Matthew Kroening

 *

 */

#include "../config.h"

#include "aprs.h"

#include "ax25.h"

#include "gps.h"

#include "sensordata.h"

#include <stdio.h>

float meters_to_feet(float m)

{

  // 10000 ft = 3048 m

  return m / 0.3048;

}

void aprs_send()

{

  const struct s_address addresses[] = { 

    {D_CALLSIGN, D_CALLSIGN_ID},  // Destination callsign

    {S_CALLSIGN, S_CALLSIGN_ID},  // Source callsign (-11 = balloon, -9 = car)

#ifdef DIGI_PATH1

    {DIGI_PATH1, DIGI_PATH1_TTL}, // Digi1 (first digi in the chain)

#endif

#ifdef DIGI_PATH2

    {DIGI_PATH2, DIGI_PATH2_TTL}, // Digi2 (second digi in the chain)

#endif

  };

	// emz: modified this to get the size of the first address rather than the size of the struct itself, which fails

  ax25_send_header(addresses, sizeof(addresses)/sizeof(addresses[0]));

  ax25_send_byte('/');                // Report w/ timestamp, no APRS messaging. $ = NMEA raw data

  // ax25_send_string("021709z");     // 021709z = 2nd day of the month, 17:09 zulu (UTC/GMT)

  ax25_send_string(get_dayofmonth()); ///! Needs to be day hour minute        // 170915 = 17h:09m:15s zulu (not allowed in Status Reports)

  ax25_send_string(get_timestamp()); 

  ax25_send_byte('z'); // zulu time. h for nonzulu

  ax25_send_string(get_latitude());     // Lat: 38deg and 22.20 min (.20 are NOT seconds, but 1/100th of minutes)

  ax25_send_byte('N');

  ax25_send_byte('/');                // Symbol table

  ax25_send_string(get_longitude());     // Lon: 000deg and 25.80 min

  ax25_send_byte('W');

  ax25_send_byte('O');                // Symbol: O=balloon, -=QTH

  ax25_send_byte('/');                // and

  //snprintf(temp, 4, "%03d", (int)(gps_speed + 0.5));

  ax25_send_string(get_speedKnots());             // speed (knots)

  /*

  ax25_send_string("/A=");            // Altitude (feet). Goes anywhere in the comment area

  snprintf(temp, 7, "%06ld", (long)(meters_to_feet(gps_altitude) + 0.5));

  ax25_send_string(temp);

  ax25_send_string("/Ti=");

  snprintf(temp, 6, "%d", 122);//sensors_int_lm60()); -- PUT SENSOR DATA HERE

  ax25_send_string(temp);

  ax25_send_string("/Te=");

  snprintf(temp, 6, "%d", 123);//sensors_ext_lm60());

  ax25_send_string(temp);

  ax25_send_string("/V=");

  snprintf(temp, 6, "%d", 123);//sensors_vin());

  ax25_send_string(temp);

  */

  ax25_send_byte(' ');

  ax25_send_string(slavesensors_getAPRScomment());

  ax25_send_footer();

  ax25_flush_frame();                 // Tell the modem to go

}

#include <inttypes.h>

#include <compat/twi.h>

#include "../config.h"

#include "i2c.h"

/* I2C clock in Hz */

#define SCL_CLOCK  100000L

/*************************************************************************

#ifndef I2C_H_

#define I2C_H_

#if (__GNUC__ * 100 + __GNUC_MINOR__) < 304

#error "This library requires AVR-GCC 3.4 or later, update to newer AVR-GCC compiler !"

#endif

#include <avr/io.h>

/** defines the data direction (reading from I2C device) in i2c_start(),i2c_rep_start() */

	LED_BUZZ,

};

typedef struct {uint8_t* direction; uint8_t* port; uint8_t pin;} led_t;

// Match order of leds enum

static led_t ledList[] = {

	{&DDRA, &PORTA, PA1}, // ACT0

	{&DDRA, &PORTA, PA2}, // ACT1

	{&DDRA, &PORTA, PA3}, // ACT2

	{&DDRA, &PORTA, PA4}, // ACT3

	{&DDRB, &PORTB, PB4}, // POWER

	{&DDRB, &PORTB, PB3}, // STATUS

	{&DDRB, &PORTB, PB2}, // ERROR

	{&DDRD, &PORTD, PD6}, // SIDEBOARD

	{&DDRD, &PORTD, PD5}, // ACTIVITY

	{&DDRD, &PORTD, PD4}, // CYCLE

	{&DDRA, &PORTA, PA6}, // HEAT

	{&DDRA, &PORTA, PA7}, // BUZZER

};

#define NUM_LEDS 12

void led_setup();

void led_on(uint8_t led);

char commentBuffer[128];

// [A-30.5 B45.64 C99542]"

char* slavesensors_getAPRScomment() {

	snprintf(commentBuffer,128, "T%d S%s V%s H%s", sensors_getBoardTemp(), get_sv(), get_speedKnots(), get_hdop());

	return commentBuffer;

}

bool dataWasReady = false;

void sensordata_logvalues() {

	// Generate CSV header after we have queried all slaves once

	if(slavesensors_dataReady()) {

		// Only generate/write header the first time data is ready

		if(!dataWasReady) {

			#define CSV_HEADER_SIZE 512

			char csvHeader[CSV_HEADER_SIZE];

			csvHeader[0] = 0x00;

						snprintf(csvHeader + strlen(csvHeader), CSV_HEADER_SIZE-strlen(csvHeader),"%s-%s,", slavesensors_slavename(i), slavesensors_getLabel(j));

					}

				}

			}

			// Terminate header string and write to SD card

			snprintf(csvHeader + strlen(csvHeader), CSV_HEADER_SIZE-strlen(csvHeader),"\r\n");

			logger_log(csvHeader);

			dataWasReady = true;

		}

		// Write CSV sensor values to SD card

		logbuf[0] = 0x00;

		snprintf(logbuf, 256, "%lu,%d,%s,%s,%s,%s,%s,%s,%s,", time_millis(), sensors_getBoardTemp(),get_timestamp(),get_latitude(),get_longitude(),get_speedKnots(),get_hdop(), get_course(), get_sv());

		for(int i=0; i<MAX_NUM_SLAVES; i++) {

			for(int j=0; j<MAX_NUM_SENSORS; j++) {

				int32_t tmp = sensordata_get(i, j);

				if(tmp != -2111111111) {

					snprintf(logbuf + strlen(logbuf),256-strlen(logbuf)," %ld,", tmp);

				}

			}

		}

		snprintf(logbuf + strlen(logbuf),256-strlen(logbuf),"\r\n");

#include <string.h>

#include <util/delay.h>

#include <avr/wdt.h>

#include <avr/pgmspace.h>

#include "serial.h"

#include "serparser.h"

#include "slavesensors.h"

#include "sensordata.h"

#include "led.h"

#include "looptime.h"

// Label lookup table

const char label_0[] PROGMEM = "BoardTemp";

const char label_1[] PROGMEM = "HeaterStatus";

const char label_2[] PROGMEM = "BatteryLevel";

const char label_3[] PROGMEM = "AirTemp";

const char label_4[] PROGMEM = "AmbientLight";

const char label_5[] PROGMEM = "Humidity";

const char label_6[] PROGMEM = "Pressure";

const char label_7[] PROGMEM = "Altitude";

const char label_8[] PROGMEM = "CPM-Radiation";

const char *const labelLookup[] PROGMEM =

{

	label_0,

	label_1,

	label_2,

	label_3,

	label_4,

	label_5,

	label_6,

	label_7,

	label_8,

};

char* slavesensors_getLabel(uint8_t sensorID) {

	if(sensorID < 9)

	{

		return labelBuffer;

	}

	else {

		return NULL;

	}

}

uint8_t currentSlave = 0;

uint8_t currentSlaveSensor = 0;

bool requesting = false;

void slavesensors_setup() 

{

}

//#define DEBUG_NETWORKSCAN

//#define DEBUG_GETSLAVEDATA

char* bufPtr = 0x00;

static char slaveAddressLow[MAX_NUM_SLAVES][9];

static char slaveAddressHigh[MAX_NUM_SLAVES][9];

uint8_t loggerIndex = 255;

uint8_t nodeCount = 0;

bool dataReady = false;

char* slavesensors_slavename(uint8_t id) {

	return slaveNames[id];

}

void slavesensors_network_scan() {

	serial0_ioff();

			// If we're starting a new block but got a newline instead, we're done!

			if(lineCount == 0 && strcmp(bufPtr, "") == 0) {

				break;			

			}

			if(lineCount == 1) {

				strncpy(slaveAddressHigh[nodeCount],bufPtr, 9);

			}

			else if(lineCount == 2) {

				strncpy(slaveAddressLow[nodeCount],bufPtr, 9);

			}

			else if(lineCount == 3) {

			}

			// If we've finished one chunk (including the newline after it). Can't be else if because it controls increment.

			if(lineCount == 9) {

				// bufPtr should be null at this point, because we read in a newline after one chunk

				nodeCount++;

				lineCount = 0;

			}

			else {

				lineCount++;

			}