#ifndef CONFIG_H_

 #define CONFIG_H_

 #define F_CPU 11059200				// Clock frequency (used in calculations)

//Serial

#define USART0_BAUDRATE 115200

#define USART1_BAUDRATE 115200 

// Circular serial buffer size. Must be at least MAX_CMD_LEN + 5

#define BUFFER_SIZE 32

// Maximum payload size of command

#define MAX_PAYLOAD_LEN 16

// Number of datatypes to transmit per module type

#define DATATYPES_GENERIC 3

#define DATATYPES_SENSOR 8

#define DATATYPES_GEIGER 4

#define DATATYPES_CAMERA 3

//Sensors and IO

#define SENSOR_LOOP 200				// Frequency of sensor reads (in ms) (should be 200)

 //I2C Addresses

 #define EEPROM_ADDR 0xA0		// Read 0xA1 - Write 0xA0

 #define BOARDTEMP_ADDR 0x90	// Read 0x91 - Write 0x90

 #define PRESSURE_ADDR 0xEE		// Read 0xEF - Write 0xEE

 #define HUMID_ADDR 0x27		// Read 0x28 - Write 0x27

 #define LIGHT_ADDR 0x94		// Read 0x95 - Write 0x94

 #define ACCEL_ADDR	0x38		// Read 0x39 - Write 0x38

 #define RTC_ADDR 0xB2			//DEBUG [Used for testing]      // Read 0xA3 - Write 0xA2

 #endif /* CONFIG_H_ */

 void modules_sensors()

 {

	// Gathers data and performs functions for sensor daughter board

	sensors_readBoardTemp();		//Data Read

	sensors_readSpiTemp();			//Data Read	

	sensors_readPressure();			//Data Read

	sensors_readHumid();			//Data Read

	sensors_readLux();				//Data Read

 }

 void modules_geiger()

 {

	// No data gatering function needed for geiger daughter board

		// This is taken care of in interrupt (See geiger.c)

 }

 void modules_cameras()

 {

	// Gathers data and performs functions for cameras daughter board

		//cameras_readAccelXYZ();

 } 

#include <stdio.h>

#include <stdbool.h>

#include <inttypes.h>

#include <avr/io.h>

#include <compat/twi.h>

#include <util/delay.h>

#include <avr/cpufunc.h>

#include <avr/interrupt.h>

#include <avr/wdt.h>

#include "modules.h"

#include "lib/serial.h"

#include "lib/serparser.h"

#include "lib/led.h"

#include "lib/inputOutput.h"

#include "lib/i2c.h"

#include "lib/spi.h"

#include "lib/geiger.h"

#include "lib/sensors.h"

#include "lib/cameras.h"

#include "lib/loopTimer.h"

#include "lib/masterComm.h"

#include "lib/watchdog.h"

bool WDTreset = false;

void micro_setup()

{

	// Generic microcontroller config options

	WDTreset = ((MCUSR & 0b00001000) > 0);	// Check if WDT reset occured

	MCUSR = 0;		// Clear reset flags

	wdt_disable();	// Disable WDT

	_delay_ms(20);	// Power debounce

	sei();			// Enable interrupts

}

int main(void)

{

	// Initialize	

	micro_setup();			// Generic microcontroller config options

	time_setup();			// Setup loop timer and interrupts (TIMER0)

	watchdog_setup();		// Setup watchdog timer

	led_configure();		// Configure ports and registers for LED operation

	io_configure();			// Configure IO ports and registers

	i2c_init();				// Setup I2C

		masterComm_checkParser();	//Checks parser for data requests from master

		// Main slave operations

		if ((time_millis() - lastLoop) > SENSOR_LOOP)	// Uses program timer to run every so often. Time interval defined in config.h

		{

			led_on(0);

			sensors_readBatt();				// Read Battery level

			sensors_readBoardTemp();		// Read board temperature sensor (Common on all slaves) (Data Read)

			modules_run(io_getModuleId());	// Runs specific module functions (like data reading)

			io_regulateTemp();			// Gets board temperature and enables heater if below threshold

			snprintf(buff,128,"|ModuleID: %u |BoardTemp: %i |Millis: %lu |Lux: %lu |Press: %lu |Altitude: %lu |Batt: %u |Humidity: %u |spiTemp: %i \r\n ",io_getModuleId(),sensors_getBoardTemp(),time_millis(),sensors_getLux(),sensors_getPressure(),sensors_getAltitude(),sensors_getBatt(),sensors_getHumid(),sensors_getSpiTemp()); //DEBUG

			serial1_sendString(buff); //DEBUG

			led_off(0);

			lastLoop = time_millis();

// Writes ID to EEPROM, change for all modules and delete after programming

// 0 is for generic setup,	 1 is for sensors,	 2 is for Geiger,	3 is for cameras

//i2c_write(EEPROM_ADDR, 0x05, 0x03);			

		}

    }

	return 0;

}

		/********Examples of data reading and getting******************

		x = geiger_getCpm();				//Data get

		x = sensors_getSpiTemp();			//Data get

		x = sensors_getBoardTemp();			//Data get

		sensors_readSpiTemp();				//Data Read

		sensors_readBoardTemp();			//Data Read

		led_output(0xFF);					//Output value to LED array

		i2c_write(RTC_ADDR, 0x05, 0x3A);	//i2c Write Example

		PORTA &= ~(1 << PA1);	//OFF

		PORTA |= (1 << PA1);	//ON

		PORTB ^= (1 << PB0);	//Toggle