seniordesign-firmware Changeset - c20bdd0c7746

Changeset - c20bdd0c7746

Parent rev.

Child rev.

[Not reviewed]

default

0 3 0

ethanzonca@CL-ENS241-08.cedarville.edu - 12 years ago 2013-03-26 17:03:10
ethanzonca@CL-ENS241-08.cedarville.edu

Enable blackout, change heater thresh to reasonable level, tweak failsafe and minduration triggers for buzzer, add humidity data to APRS message

2 files changed with 13 insertions and 6 deletions:

master/master/config.h

master/master/lib/sensordata.c

0 comments (0 inline, 0 general)

master/master/config.h

➞

Show inline comments

@@ @@ -22,36 +22,36 @@ @@
 #define F_CPU 11059200
 #define BOARDTEMP_ADDR 0x90
 // --------------------------------------------------------------------------
 // Module config (master.c)
 // --------------------------------------------------------------------------
 // Debug Output
 //#define DEBUG_OUTPUT
 // Blackout (turn off all but power LEDs)
-//#define BLACKOUT_ENABLE
 #define BLACKOUT_ENABLE
 #define BLACKOUT_TIMEOUT 300000 // Blackout after 5 minutes (hopefully after fix)
 // Board heater setpoint
-#define HEATER_THRESHOLD 80
+#define HEATER_THRESHOLD 5 // Regulate to 5 degrees celsius
 // Touchdown buzzer
 #define BUZZER_RATE 5000
 #define BUZZER_DURATION 1000
 #define BUZZER_FAILSAFE_DURATION 600000
 #define BUZZER_TRIGGER_MINDURATION 1
 #define BUZZER_TRIGGER_MAXALTITUDE 1
 #define BUZZER_FAILSAFE_DURATION  12600000 // 3.5hr
 #define BUZZER_TRIGGER_MINDURATION 3600000 // 1 hour
 #define BUZZER_TRIGGER_MAXALTITUDE 180
 // --------------------------------------------------------------------------
 // Error Codes config (logger.c)
 // --------------------------------------------------------------------------
 // SD Card
 #define ERROR_SLAVETIMEOUT 0
 #define ERROR_SD_INIT 1
 #define ERROR_SD_PARTITION 2
 #define ERROR_SD_FILE 3
 #define ERROR_XBEETIMEOUT 4
 #define ERROR_FATAL 5
@@ @@ -155,22 +155,22 @@ @@
 // --------------------------------------------------------------------------
 // Logger config (logger.c)
 // --------------------------------------------------------------------------
 // Log number EEPROM address (this number is incremented on boot, used for filenames)
 #define LOGGER_ID_EEPROM_ADDR 0x10
 // Watchdog save/restore of program timer
 #define WATCHDOG_PROGTIMER_EEPROM_ADDR 0x20
 // Written to the beginning of every log file
-#define LOGGER_HEADERTEXT "HAB Control Master - 1.0\n"
+#define LOGGER_HEADERTEXT "HAB Control Master - 1.1\n"
 // Log to SD card every X milliseconds
 #define LOGGER_RATE 1000
 // LED cycle indicator speed
 #define LEDCYCLE_RATE 100
 #endif /* CONFIG_H_ */
@@ \ No newline at end of file @@

master/master/lib/sensordata.c

➞

Show inline comments

@@ @@ -95,24 +95,31 @@ char* slavesensors_getAPRScomment(char* @@
 			if(val != -2111111111) {
 				uint16_t len = strlen(commentBuffer);
 				snprintf(commentBuffer + len, bufferSize-len, "~P%li",val);
+			}
 			// Air Temperature
 			val = sensordata_get(i, SENSOR_AIRTEMP);
 			if(val != -2111111111) {
 				uint16_t len = strlen(commentBuffer);
 				snprintf(commentBuffer + len, bufferSize-len, "~C%li",val);
+			}
 			// Humidity
 			val = sensordata_get(i, SENSOR_HUMIDITY);
 			if(val != -2111111111) {
 				uint16_t len = strlen(commentBuffer);
 				snprintf(commentBuffer + len, bufferSize-len, "~H%li",val);
+			}
 			// Altitude
 			val = sensordata_get(i, SENSOR_ALTITUDE);
 			if(val != -2111111111) {
 				uint16_t len = strlen(commentBuffer);
 				snprintf(commentBuffer + len, bufferSize-len, "~A%li",val);
+			}
 			// Radiation
 			val = sensordata_get(i, SENSOR_CPM_RADIATION);
 			if(val != -2111111111) {
 				uint16_t len = strlen(commentBuffer);
 				snprintf(commentBuffer + len, bufferSize-len, "~R%li",val);

0 comments (0 inline, 0 general)