therm Changeset - 149610e94cf9 · protofusion repositories

Changeset - 149610e94cf9

Parent rev.

Child rev.

[Not reviewed]

cortex-f0

0 3 2

Ethan Zonca - 9 years ago 2015-06-01 17:48:05
ez@ethanzonca.com

Moved save/restore of settings to new file

5 files changed with 81 insertions and 74 deletions:

Makefile

display.c

main.c

storage.c

storage.h

0 comments (0 inline, 0 general)

Makefile

➞

Show inline comments

 # STM32F0xx Makefile
 # #####################################
+#
 # Part of the uCtools project
 # uctools.github.com
+#
 #######################################
 # user configuration:
 #######################################
 # SOURCES: list of sources in the user application
 SOURCES = main.c usbd_conf.c usbd_cdc_if.c usb_device.c usbd_desc.c stm32f0xx_hal_msp.c stm32f0xx_it.c system_stm32f0xx.c gpio.c spi.c ssd1306.c stringhelpers.c display.c bootlib.c
+SOURCES = main.c usbd_conf.c usbd_cdc_if.c usb_device.c usbd_desc.c stm32f0xx_hal_msp.c stm32f0xx_it.c system_stm32f0xx.c gpio.c spi.c ssd1306.c stringhelpers.c display.c bootlib.c storage.c
 # TARGET: name of the user application
 TARGET = main
 # BUILD_DIR: directory to place output files in
 BUILD_DIR = build
 # LD_SCRIPT: location of the linker script
 LD_SCRIPT = stm32f042c6_flash.ld
 # USER_DEFS user defined macros
 USER_DEFS = -D HSI48_VALUE=48000000 -D HSE_VALUE=16000000

display.c

➞

Show inline comments

@@ @@ -365,25 +365,25 @@ void display_process(therm_settings_t* s @@
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->temp_offset, tempstr, 10);
             ssd1306_DrawString("O=", 1, 45);
             ssd1306_DrawString("    ", 1, 57);
             ssd1306_DrawString(tempstr, 1, 57);
             ssd1306_DrawString("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 save_settings();
+                save_settings(&set);
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input_signed(&set->temp_offset);
+            }
             // Event Handler
             // N/A
         } break;
@@ @@ -392,25 +392,25 @@ void display_process(therm_settings_t* s @@
             // Write text to OLED
             // [ therm : preheating brew ]
             // [ 30 => 120 C             ]
             ssd1306_DrawString("Preheating...", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->setpoint_brew;
             // Button handler
             if(SW_BTN_PRESSED) {
 		save_setpoints(); // TODO: Check for mod
+		save_setpoints(&set); // TODO: Check for mod
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input(&set->setpoint_brew);
+            }
             // Event Handler
             if(status->temp >= status->setpoint) {
                 status->state = STATE_MAINTAIN_BREW;
+            }
         } break;
@@ @@ -419,25 +419,25 @@ void display_process(therm_settings_t* s @@
+        {
             // Write text to OLED
             // [ therm : ready to brew ]
             // [ 30 => 120 C           ]
             ssd1306_DrawString("Preheated!", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->setpoint_brew;
             // Button handler
             if(SW_BTN_PRESSED) {
 		save_setpoints(); // TODO: Check for mod
+		save_setpoints(&set); // TODO: Check for mod
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input(&set->setpoint_brew);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_PREHEAT_STEAM:
@@ @@ -445,25 +445,25 @@ void display_process(therm_settings_t* s @@
             // Write text to OLED
             // [ therm : preheating steam ]
             // [ 30 => 120 C           ]
             ssd1306_DrawString("Preheating...", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->setpoint_steam;
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
 		save_setpoints(); // TODO: Check for mod
+		save_setpoints(&set); // TODO: Check for mod
+            }
             else {
                 user_input(&set->setpoint_steam);
+            }
             // Event Handler
             if(status->temp >= status->setpoint) {
                 status->state = STATE_MAINTAIN_STEAM;
+            }
         } break;
@@ @@ -472,25 +472,25 @@ void display_process(therm_settings_t* s @@
             // Write text to OLED
             // [ therm : ready to steam ]
             // [ 30 => 120 C            ]
             ssd1306_DrawString("Ready to Steam!", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->setpoint_steam;
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
 		save_setpoints(); // TODO: Check for mod
+		save_setpoints(&set); // TODO: Check for mod
+            }
             else {
                 user_input(&set->setpoint_steam);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_TC_ERROR:
+        {

main.c

➞

Show inline comments

 #include "stm32f0xx_hal.h"
 #include "config.h"
 #include "states.h"
 #include "ssd1306.h"
 #include "gpio.h"
 #include "spi.h"
 #include "stringhelpers.h"
 #include "display.h"
 #include "storage.h"
 #include "usb_device.h"
 #include "usbd_cdc_if.h"
 // Prototypes
 // Move to header file
 void process();
 void restore_settings();
 void save_settings();
 void save_setpoints();
 void SystemClock_Config(void);
 therm_settings_t set;
 therm_status_t status;
 // Globalish setting vars
 SPI_HandleTypeDef hspi1;
 static __IO uint32_t TimingDelay;
 void deinit(void)
+{
@@ @@ -79,25 +77,25 @@ int main(void) @@
     set.setpoint_brew = 0;
     set.setpoint_steam = 0;
     // Default status
     status.temp = 0;
     status.temp_frac = 0;
     status.state_resume = 0;
     status.state = STATE_IDLE;
     status.setpoint = 0;
     status.pid_enabled = 0;
     // Load settings (if any) from EEPROM
     restore_settings();
+    restore_settings(&set);
     // Go to brew instead of idle if configured thusly
     if(set.boottobrew)
       status.state = STATE_PREHEAT_BREW;
     // Startup screen
     ssd1306_DrawString("therm v0.2", 1, 40);
     ssd1306_DrawString("protofusion.org/therm", 3, 0);
     HAL_Delay(1500);
     ssd1306_clearscreen();
@@ @@ -332,77 +330,13 @@ void process() @@
         itoa_fp(status.temp, status.temp_frac, tempstr);
         uint8_t numlen = strlen(tempstr);
         tempstr[numlen] = '\r';
         tempstr[numlen+1] = '\n';
         CDC_Transmit_FS(tempstr, numlen+2);
        // while(CDC_Transmit_FS("\r\n", 2) == USBD_BUSY);
         last_vcp_tx = ticks;
+    }
+}
 void save_settings()
+{
     // TODO: Rework with FLASH read/write
 /*
    Minimal_EEPROM_Unlock();
     // Try programming a word at an address divisible by 4
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_BOOTTOBREW, boottobrew);
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_WINDUP_GUARD, windup_guard);
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_P, k_p);
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_I, k_i);
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_D, k_d);
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_UNITS, temp_units);
     Minimal_EEPROM_Lock();
 */
+}
 void save_setpoints()
+{
     // TODO: Rework with FLASH read/write
 /*
     Minimal_EEPROM_Unlock();
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_BREWTEMP, setpoint_brew);
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_STEAMTEMP, setpoint_steam);
     Minimal_EEPROM_Lock();
 */
+}
 // TODO: Make a struct that has all settings in it. Pass by ref to this func in a library.
 void restore_settings()
+{
     // TODO: Rework with FLASH read/write
 /*    Minimal_EEPROM_Unlock();
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     boottobrew = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_BOOTTOBREW));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     windup_guard = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_WINDUP_GUARD));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     k_p = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_P));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     k_i = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_I));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     k_d = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_D));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     setpoint_brew = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_BREWTEMP));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     setpoint_steam = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_STEAMTEMP));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     temp_units = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_UNITS));
     Minimal_EEPROM_Lock(); */
+}
 // vim:softtabstop=4 shiftwidth=4 expandtab

storage.c

➞

Show inline comments

@@ new file 100644 @@
 #include "stm32f0xx_hal.h"
 #include "states.h"
 void save_settings(therm_settings_t *tosave)
+{
     // TODO: Rework with FLASH read/write
 /*
    Minimal_EEPROM_Unlock();
     // Try programming a word at an address divisible by 4
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_BOOTTOBREW, boottobrew);
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_WINDUP_GUARD, windup_guard);
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_P, k_p);
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_I, k_i);
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_D, k_d);
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_UNITS, temp_units);
     Minimal_EEPROM_Lock();
 */
+}
 void save_setpoints(therm_settings_t *tosave)
+{
     // TODO: Rework with FLASH read/write
 /*
     Minimal_EEPROM_Unlock();
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_BREWTEMP, setpoint_brew);
     Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_STEAMTEMP, setpoint_steam);
     Minimal_EEPROM_Lock();
 */
+}
 // TODO: Make a struct that has all settings in it. Pass by ref to this func in a library.
 void restore_settings(therm_settings_t *tosave)
+{
     // TODO: Rework with FLASH read/write
 /*    Minimal_EEPROM_Unlock();
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     boottobrew = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_BOOTTOBREW));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     windup_guard = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_WINDUP_GUARD));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     k_p = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_P));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     k_i = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_I));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     k_d = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_D));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     setpoint_brew = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_BREWTEMP));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     setpoint_steam = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_STEAMTEMP));
     while(Minimal_FLASH_GetStatus()==FLASH_BUSY);
     temp_units = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_UNITS));
     Minimal_EEPROM_Lock(); */
+}

storage.h

➞

Show inline comments

@@ new file 100644 @@
 #ifndef STORAGE_H
 #define STORAGE_H
 void save_settings(therm_settings_t *tosave);
 void save_setpoints(therm_settings_t *tosave);
 void restore_settings(therm_settings_t *tosave);
 #endif

0 comments (0 inline, 0 general)