SRC+=eeprom_min.c

SRC+=gpio.c

SRC+=spi.c

SRC+=stringhelpers.c

# Discovery Source Files

#SRC+=stm32f4_discovery_lis302dl.c

#SRC+=stm32f4_discovery.c

#SRC+=stm32f4_discovery_audio_codec.c

# Standard Peripheral Source Files

SRC+=stm32f0xx_syscfg.c

SRC+=misc.c

SRC+=stm32f0xx_adc.c

SRC+=stm32f0xx_dac.c

SRC+=stm32f0xx_dma.c

SRC+=stm32f0xx_exti.c

SRC+=stm32f0xx_flash.c

SRC+=stm32f0xx_gpio.c

SRC+=stm32f0xx_i2c.c

SRC+=stm32f0xx_rcc.c

SRC+=stm32f0xx_spi.c

SRC+=stm32f0xx_tim.c

# USB Source Files

SRC+=usb_core.c

SRC+=usb_init.c

SRC+=usb_int.c

SRC+=usb_mem.c

SRC+=usb_regs.c

SRC+=usb_sil.c

SRC+=hw_config.c

SRC+=usb_desc.c

SRC+=usb_endp.c

SRC+=usb_istr.c

SRC+=usb_prop.c

SRC+=usb_pwr.c

CDEFS=-DUSE_STDPERIPH_DRIVER

CDEFS+=-DSTM32F0XX

CDEFS+=-DMANGUSTA_DISCOVERY

#CDEFS+=-DUSE_USB_OTG_FS

# EMZ FIXME

CDEFS+=-DHSE_VALUE=8000000

#EMZ Optimized: 

# Default:  MCUFLAGS=-mcpu=cortex-m3 -mthumb -ffunction-sections -fdata-sections

#MCUFLAGS=-mcpu=cortex-m4 -mthumb -mlittle-endian -mfpu=fpa -mfloat-abi=hard -mthumb-interwork

#MCUFLAGS=-mcpu=cortex-m4 -mfpu=vfpv4-sp-d16 -mfloat-abi=hard

COMMONFLAGS=-O$(OPTLVL) -g -Wall

CFLAGS=$(COMMONFLAGS) $(MCUFLAGS) $(INCLUDE) $(CDEFS)

LDLIBS=

LDFLAGS=$(COMMONFLAGS) -fno-exceptions -ffunction-sections -fdata-sections \

        -nostartfiles -Wl,--gc-sections,-T$(LINKER_SCRIPT)

#####

#####

OBJ = $(SRC:%.c=%.o) $(ASRC:%.s=%.o)

CC=$(TOOLCHAIN_PATH)/$(TOOLCHAIN_PREFIX)-gcc

LD=$(TOOLCHAIN_PATH)/$(TOOLCHAIN_PREFIX)-gcc

OBJCOPY=$(TOOLCHAIN_PATH)/$(TOOLCHAIN_PREFIX)-objcopy

AS=$(TOOLCHAIN_PATH)/$(TOOLCHAIN_PREFIX)-as

AR=$(TOOLCHAIN_PATH)/$(TOOLCHAIN_PREFIX)-ar

GDB=$(TOOLCHAIN_PATH)/$(TOOLCHAIN_PREFIX)-gdb

SIZE=$(TOOLCHAIN_PATH)/$(TOOLCHAIN_PREFIX)-size

all: $(OBJ)

	$(CC) -o $(TARGET).elf $(LDFLAGS) $(OBJ)	$(LDLIBS)

	$(OBJCOPY) -O ihex   $(TARGET).elf $(TARGET).hex

	$(OBJCOPY) -O binary $(TARGET).elf $(TARGET).bin

.PHONY: clean

clean:

	rm -f $(OBJ)

	rm -f $(TARGET).elf

	rm -f $(TARGET).hex

	rm -f $(TARGET).bin

# Display size

size: $(TARGET).elf

	@echo Invoking: ARM GNU Print Size

	$(SIZE) --format=berkeley $<

	@echo

#ifndef EEPROM_MIN_H

#define EEPROM_MIN_H

#define EEPROM_BASE_ADDR    0x08080000    

#define EEPROM_BYTE_SIZE    0x0FFF  

#define EEPROM_ADDR_WINDUP_GUARD 	0x001C

#define EEPROM_ADDR_BOOTTOBREW		0x0020

#define EEPROM_ADDR_K_P			0x0024

#define EEPROM_ADDR_K_I			0x0028

#define EEPROM_ADDR_K_D			0x002C

#define EEPROM_ADDR_BREWTEMP		0x0030

#define EEPROM_ADDR_STEAMTEMP		0x0034

void Minimal_EEPROM_Unlock(void);

void Minimal_EEPROM_Lock(void);

FLASH_Status Minimal_FLASH_GetStatus(void);

FLASH_Status Minimal_FLASH_WaitForLastOperation(uint32_t Timeout);

void Minimal_EEPROM_ProgramWord(uint32_t Address, uint32_t Data);

#endif

#include "main.h"

#include "stm32l100c_discovery.h"

#include "ssd1306.h"

#include "config.h"

#include "eeprom_min.h"

#include "gpio.h"

#include "spi.h"

// USB includes

#include "hw_config.h"

#include "usb_lib.h"

#include "usb_desc.h"

#include "usb_pwr.h"

#include "stringhelpers.h"

// TODO: Grab buttonpresses with interrupts

// USB Supporting Vars

extern __IO uint8_t Receive_Buffer[64];

extern __IO  uint32_t Receive_length ;

extern __IO  uint32_t length ;

uint8_t Send_Buffer[64];

uint32_t packet_sent=1;

uint32_t packet_receive=1;

// Globalish setting vars

uint8_t boottobrew = 0;

uint16_t windup_guard = 1;

uint16_t k_p = 1;

uint16_t k_i = 1;

uint16_t k_d = 1;

// ISR ticks var

volatile uint32_t ticks = 0;

int16_t setpoint_brew = 0;

int16_t setpoint_steam = 0;

// State definition

enum state {

    STATE_IDLE = 0,

    STATE_SETP,

    STATE_SETI,

    STATE_SETD,

    STATE_SETWINDUP,

    STATE_SETBOOTTOBREW,

    STATE_PREHEAT_BREW,

    STATE_MAINTAIN_BREW,

    STATE_PREHEAT_STEAM,

    STATE_MAINTAIN_STEAM,

};

uint8_t state = STATE_IDLE;

static __IO uint32_t TimingDelay;

// Move to header file

void process();

void machine();

void restore_settings();

void save_settings();

void save_setpoints();

int main(void)

{

    // Init clocks

    SystemInit();

    // Init GPIO

    init_gpio();

    // Turn on power LED

    GPIO_SetBits(LED_POWER);

    // TODO: Awesome pwm of power LED (TIM4_CH4 or TIM11_CH1)

    // Configure 1ms SysTick (change if more temporal resolution needed) 

    RCC_ClocksTypeDef RCC_Clocks;

    RCC_GetClocksFreq(&RCC_Clocks);

    SysTick_Config(RCC_Clocks.HCLK_Frequency / 1000);

    // Init SPI busses

    init_spi();

    // Init OLED over SPI

    ssd1306_Init();

    ssd1306_clearscreen();

    // Check for problems on startup

    if(clock_fail) {

        //ssd1306_DrawStringBig("ERROR: Check Xtal", 2, 0);

        ssd1306_DrawStringBig("NO XTAL", 2, 0);

        delay(1000);

        ssd1306_clearscreen();

    }

    // Init USB

    //Set_System(); // hw_config.h

    Set_USBClock();

    USB_Interrupts_Config();

    USB_Init();

    //SYSCFG_USBPuCmd(ENABLE);

    //PowerOn();

    // Startup screen 

    ssd1306_DrawString("therm v0.1", 1, 40);

    ssd1306_DrawString("protofusion.org/therm", 3, 0);

    delay(1500);

    ssd1306_clearscreen();

    restore_settings();

    if(boottobrew)

      state = STATE_PREHEAT_BREW; // Go to brew instead of idle if configured thusly

    GPIO_ResetBits(LED_STAT);

    // Main loop

    while(1)

    {

        // Process sensor inputs

        process();

        // Run state machine

        machine(); 

    }

}

// Read temperature and update global temp vars

uint8_t temp_frac = 0;

void update_temp() {

    // Assert CS

    GPIO_ResetBits(MAX_CS);

    delay(1);

    // This may not clock at all... might need to send 16 bits first

    SPI_I2S_SendData(SPI2, 0xAAAA); // send dummy data

    //SPI_I2S_SendData(SPI2, 0xAA); // send dummy data

    uint16_t temp_pre = SPI_I2S_ReceiveData(SPI2);

    if(temp_pre & 0b0000000000000010) {

    }

        temp = 0;

        temp_frac = 0;

    }

    else 

    {

        uint8_t sign = temp >> 15;// top bit is sign

        temp_pre = temp_pre >> 2; // Drop 2 lowest bits

        temp_frac = temp_pre & 0b11; // get fractional part

        temp_frac *= 25; // each bit is .25 a degree, up to fixed point

        temp_pre = temp_pre >> 2; // Drop 2 fractional bits 

        if(sign) {

            temp = -temp_pre;

        }

        else {

            temp = temp_pre;

        }

    }

    // Deassert CS

    delay(1);

    GPIO_SetBits(MAX_CS);

}

// PID implementation

// TODO: Make struct that has the last_temp and i_state in it, pass by ref. Make struct that has other input values maybe.

int16_t last_pid_temp = 0;

uint8_t last_pid_temp_frac = 0;

int16_t i_state = 0;

int16_t update_pid(uint16_t k_p, uint16_t k_i, uint16_t k_d, int16_t temp, uint8_t temp_frac, int16_t setpoint) 

{

  // Calculate instantaneous error

  int16_t error = (int16_t)setpoint - (int16_t)temp; // TODO: Use fixed point fraction

  // Proportional component

  int16_t p_term = k_p * error;

  // Error accumulator (integrator)

  i_state += error;

  // to prevent the iTerm getting huge despite lots of 

  //  error, we use a "windup guard" 

  // (this happens when the machine is first turned on and

  // it cant help be cold despite its best efforts)

  // not necessary, but this makes windup guard values 

  // relative to the current iGain

  int16_t windup_guard_res = windup_guard / k_i;  

  // Calculate integral term with windup guard 

  if (i_state > windup_guard_res) 

    i_state = windup_guard_res;

  else if (i_state < -windup_guard_res) 

    i_state = -windup_guard_res;

  int16_t i_term = k_i * i_state;

  // Calculate differential term (slope since last iteration)

  int16_t d_term = (k_d * (temp - last_pid_temp));

  // Save temperature for next iteration

  last_pid_temp = temp;

  last_pid_temp_frac = temp_frac;

  int16_t result = p_term + i_term - d_term;

            GPIO_SetBits(SSR_PIN);

            last_ssr_on = ticks;

        }

    }

    // Kill SSR after elapsed period less than SSR_PERIOD 

    if(ticks - last_ssr_on > ssr_output || ssr_output == 0)

    {

        GPIO_ResetBits(LED_STAT);

        GPIO_ResetBits(SSR_PIN);

    }

}

void draw_setpoint() {

    char tempstr[3];

    itoa_fp(temp, temp_frac, tempstr);

    ssd1306_DrawStringBig("      ", 3, 0);

    ssd1306_DrawStringBig(tempstr, 3, 0);

    ssd1306_DrawStringBig(">", 3, 74);

    itoa(setpoint, tempstr);

    ssd1306_DrawStringBig("    ", 3, 90);

    ssd1306_DrawStringBig(tempstr, 3, 90);

}

uint8_t goto_mode = 2;

// State machine

uint8_t sw_btn_last = 0;

uint8_t sw_up_last = 0;

uint8_t sw_down_last = 0;

uint8_t sw_left_last = 0;

uint8_t sw_right_last = 0;

#define SW_BTN_PRESSED (sw_btn_last == 0 && sw_btn == 1) // rising edge on buttonpress

#define SW_UP_PRESSED (sw_up_last == 0 && sw_up == 1)

#define SW_DOWN_PRESSED (sw_down_last == 0 && sw_down == 1)

#define SW_LEFT_PRESSED (sw_left_last == 0 && sw_left == 1)

#define SW_RIGHT_PRESSED (sw_right_last == 0 && sw_right == 1)

void save_settings()

{

   Minimal_EEPROM_Unlock();

    // Try programming a word at an address divisible by 4

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_BOOTTOBREW, boottobrew);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_WINDUP_GUARD, windup_guard);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_P, k_p);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_I, k_i);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_D, k_d);

    Minimal_EEPROM_Lock();

}

void save_setpoints()

{

    Minimal_EEPROM_Unlock();

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_BREWTEMP, setpoint_brew);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_STEAMTEMP, setpoint_steam); 

    Minimal_EEPROM_Lock();

}

// TODO: Make a struct that has all settings in it. Pass by ref to this func in a library.

void restore_settings()

{

    Minimal_EEPROM_Unlock();

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    boottobrew = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_BOOTTOBREW));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    windup_guard = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_WINDUP_GUARD));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    k_p = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_P));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    k_i = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_I));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    k_d = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_D));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    setpoint_brew = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_BREWTEMP));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    setpoint_steam = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_STEAMTEMP));    

    Minimal_EEPROM_Lock();

}

int16_t last_temp = 21245;

void machine()

{

    uint8_t last_state = state;

    uint8_t temp_changed = temp != last_temp;

    last_temp = temp;

    uint8_t sw_btn = !GPIO_ReadInputDataBit(SW_BTN);

    uint8_t sw_up = !GPIO_ReadInputDataBit(SW_UP);

    uint8_t sw_down = !GPIO_ReadInputDataBit(SW_DOWN);

    uint8_t sw_left = !GPIO_ReadInputDataBit(SW_LEFT);

    uint8_t sw_right = !GPIO_ReadInputDataBit(SW_RIGHT);

    switch(state)

    {

        // Idle state

        case STATE_IDLE:

        {

            // Write text to OLED

            // [ therm :: idle ]

            ssd1306_DrawString("therm :: idle ", 0, 40);

            pid_enabled = 0;

            if(temp_changed) {

                char tempstr[6];

                itoa_fp(temp, temp_frac, tempstr);

                ssd1306_DrawString("Temp: ", 3, 40);

                ssd1306_DrawString("    ", 3, 72);

                ssd1306_DrawString(tempstr, 3, 72);

            }

            ssd1306_drawlogo();

            switch(goto_mode) {

                case 2:

                {

                } break;

                case 1:

                {

                    ssd1306_DrawString("-> setup    ", 1, 40);

                } break;

                case 0:

                {

                    ssd1306_DrawString("-> reset    ", 1, 40);

                } break;

            }

            // Button handler

            if(SW_BTN_PRESSED) {

                switch(goto_mode) {

                    case 2:

                        state = STATE_PREHEAT_BREW;

                        break;

                    case 1:

                        state = STATE_SETP;

                        break;

                    case 0:

                        state = STATE_IDLE;

                        break;

                    default:

                        state = STATE_PREHEAT_BREW;

                }

            }

            else if(SW_UP_PRESSED && goto_mode < 2) {

                goto_mode++;

            }

            else if(SW_DOWN_PRESSED && goto_mode > 0) {

                goto_mode--;

            }

            // Event Handler

            // N/A

        } break;

        case STATE_SETP:

        {

            // Write text to OLED

            // [ therm :: set p ]

            // [ p = 12         ]

            ssd1306_DrawString("Proportional", 0, 40);

            ssd1306_DrawString("I=", 1, 45);

            ssd1306_DrawString("    ", 1, 57);

            ssd1306_DrawString(tempstr, 1, 57);

            ssd1306_DrawString("Press to accept", 3, 40);

            // Button handler

            if(SW_BTN_PRESSED) {

                state = STATE_SETD;

            }

            else {

                user_input(&k_i);

            }

            // Event Handler

            // N/A

        } break;

        case STATE_SETD:

        {

            // Write text to OLED

            // [ therm :: set d ]

            // [ d = 12         ]

            ssd1306_DrawString("Derivative", 0, 40);

            ssd1306_drawlogo();

            char tempstr[6];

            itoa(k_d, tempstr);

            ssd1306_DrawString("D=", 1, 45);

            ssd1306_DrawString("    ", 1, 57);

            ssd1306_DrawString(tempstr, 1, 57);

            ssd1306_DrawString("Press to accept", 3, 40);

            // Button handler

            if(SW_BTN_PRESSED) {

                state = STATE_SETWINDUP;

            }

            else {

                user_input(&k_d);

            }

            // Event Handler

            // N/A

        } break;

        case STATE_SETWINDUP:

        {

            // Write text to OLED

            // [ therm :: set windup ]

            // [ g = 12         ]

            ssd1306_DrawString("Windup Guard", 0, 40);

            ssd1306_drawlogo();

            char tempstr[6];

            itoa(windup_guard, tempstr);

            ssd1306_DrawString("G=", 1, 45);

            ssd1306_DrawString("    ", 1, 57);

            ssd1306_DrawString(tempstr, 1, 57);

            ssd1306_DrawString("Press to accept", 3, 40);

            // Button handler

            if(SW_BTN_PRESSED) {

                state = STATE_SETBOOTTOBREW;

            }

            else {

                user_input(&windup_guard);

            }

            // Event Handler

            // N/A

        } break;

        case STATE_SETBOOTTOBREW:

        {

            // Write text to OLED

            // [ therm :: set windup ]

            // [ g = 12         ]

            ssd1306_drawlogo();

            if(boottobrew)

                ssd1306_DrawString("Enabled ", 1, 70);

            else

                ssd1306_DrawString("Disabled", 1, 70);

            ssd1306_DrawString("Press to accept", 3, 40);

            // Button handler

            if(SW_BTN_PRESSED) {

            }

            else if(!GPIO_ReadInputDataBit(SW_UP)) {

                boottobrew = 1;

            }

            else if(!GPIO_ReadInputDataBit(SW_DOWN)) {

                boottobrew = 0;

            }

            // Event Handler

            // N/A

        } break;

        case STATE_PREHEAT_BREW:

        {

            // Write text to OLED

            // [ therm : preheating brew ]

            // [ 30 => 120 C             ]

            ssd1306_DrawString("Preheating...", 0, 0);

            //ssd1306_drawlogo();

            draw_setpoint();

            pid_enabled = 1;

	    setpoint = setpoint_brew;

            // Button handler

            if(SW_BTN_PRESSED) {

		save_setpoints(); // TODO: Check for mod

                state = STATE_IDLE;

            }

            else {

                user_input(&setpoint_brew);

            }

            // Event Handler

            if(temp >= setpoint) {

                state = STATE_MAINTAIN_BREW;

            }

        } break;

        case STATE_MAINTAIN_BREW:

        {

            // Write text to OLED

            // [ therm : ready to brew ]

            // [ 30 => 120 C           ]

            ssd1306_DrawString("Preheated!", 0, 0);

            //ssd1306_drawlogo();

            draw_setpoint();