#include "main.h"

#include "stm32l100c_discovery.h"

#include "ssd1306.h"

// USB includes

#include "hw_config.h"

#include "usb_lib.h"

#include "usb_desc.h"

#include "usb_pwr.h"

#define LED_POWER GPIOB,GPIO_Pin_9

#define LED_STAT  GPIOA,GPIO_Pin_15

#define MAX_CS GPIOB,GPIO_Pin_12

// TODO: Grab buttonpresses with interrupts

#define SW_BTN  GPIOB, GPIO_Pin_3

#define SW_UP   GPIOB, GPIO_Pin_7

#define SW_DOWN GPIOB, GPIO_Pin_6

#define SW_LEFT GPIOB, GPIO_Pin_5

#define SW_RIGHT GPIOB, GPIO_Pin_4

// USB Supporting Vars

extern __IO uint8_t Receive_Buffer[64];

extern __IO  uint32_t Receive_length ;

extern __IO  uint32_t length ;

uint8_t Send_Buffer[64];

uint32_t packet_sent=1;

uint32_t packet_receive=1;

static __IO uint32_t TimingDelay;

// Move to header file

void init_gpio();

void init_spi();

void process();

void machine();

int main(void)

{

    // Init clocks

    SystemInit();

    init_gpio();

    // Init USB

    //Set_USBClock();

    //USB_Interrupts_Config();

    //USB_Init();

    GPIO_SetBits(LED_POWER);

    RCC_ClocksTypeDef RCC_Clocks;

    // SysTick end of count event each 1ms

    RCC_GetClocksFreq(&RCC_Clocks);

    SysTick_Config(RCC_Clocks.HCLK_Frequency / 1000);

    GPIO_ResetBits(LED_STAT);

    Delay(100);

    GPIO_SetBits(LED_POWER);

    Delay(500);

    GPIO_ResetBits(LED_POWER);

    init_spi();

    ssd1306_Init();

    ssd1306_block_write();

    ssd1306_DrawString("Hello World!", 0, 10);

  //  ssd1306_block_write();

    while(1)

   {  

        //ssd1306_block_write();

        // Process sensor inputs [TODO: 5hz?]

        process();

        // Run state machine [TODO: 50hz?]

        machine(); 

        // probably just passed the actual port

        // TODO: Grab buttonpresses with interrupts

        uint8_t sw_btn = GPIO_ReadInputDataBit(SW_BTN);

        uint8_t sw_up = GPIO_ReadInputDataBit(SW_UP);

        uint8_t sw_down = GPIO_ReadInputDataBit(SW_DOWN);

        uint8_t sw_left = GPIO_ReadInputDataBit(SW_LEFT);

        uint8_t sw_right = GPIO_ReadInputDataBit(SW_RIGHT);

        if(!sw_btn) {

            GPIO_ToggleBits(LED_STAT);

        }

        GPIO_SetBits(LED_POWER);

        Delay(50);

        GPIO_ResetBits(LED_POWER);

        Delay(50);

    }

}

int32_t temp = 0;

int32_t setpoint = 0;

int32_t p = 1;

int32_t i = 1;

int32_t d = 1;

// Process things

void process()

{

    // Read MAX temp sensor

    GPIO_ResetBits(MAX_CS);

    // Assert CS

    // This may not clock at all... might need to send 16 bits first

    uint8_t retval = 0;//SPI_I2S_ReceiveData(SPI2);

    // Deassert CS

    GPIO_SetBits(MAX_CS);

    if((!retval || (temp & 0x2) != 0))

        return; // Comms error - this is happening right now

    if((temp & 0x4)!= 0)

        return; // Open thermocouple

    temp = (temp & 0x7FF8) >> 5;

    // TODO: Add calibration offset (linear)

    // Perform PID calculations

    // Write output to SSR

}

enum state {

    STATE_IDLE = 0,

    STATE_SETP,

    STATE_SETI,

    STATE_SETD,

    STATE_PREHEAT_BREW,

    STATE_MAINTAIN_BREW,

    STATE_PREHEAT_STEAM,

    STATE_MAINTAIN_STEAM,

};

uint8_t state = STATE_IDLE;

// State machine

void machine()

{

    switch(state)

    {

        // Idle state

        case STATE_IDLE:

        {

            // Write text to OLED

            // [ therm :: idle ]

            // Button handler

            if(GPIO_ReadInputDataBit(SW_BTN)) {

                state = STATE_SETP;

            }

            // Event Handler

            // N/A

        } break;

        case STATE_SETP:

        {

            // Write text to OLED

            // [ therm :: set p ]

            // [ p = 12         ]

            // Button handler

            if(GPIO_ReadInputDataBit(SW_BTN)) {

                state = STATE_IDLE;

            }

            // Event Handler

            // N/A

        } break;

        case STATE_SETI:

        {

            // Write text to OLED

            // [ therm :: set i ]

            // [ i = 12         ]

            // Button handler

            if(GPIO_ReadInputDataBit(SW_BTN)) {

                state = STATE_IDLE;

            }

            // Event Handler

            // N/A

        } break;

        case STATE_SETD:

        {

            // Write text to OLED

            // [ therm :: set d ]

            // [ d = 12         ]

            // Button handler

            if(GPIO_ReadInputDataBit(SW_BTN)) {

                state = STATE_IDLE;

            }

            // Event Handler

            // N/A

        } break;

        case STATE_PREHEAT_BREW:

        {

            // Write text to OLED

            // [ therm : preheating brew ]

            // [ 30 => 120 C             ]

            // Button handler

            if(GPIO_ReadInputDataBit(SW_BTN)) {

                state = STATE_IDLE;

            }

            // Event Handler

            if(temp >= setpoint) {

                state = STATE_MAINTAIN_BREW;

            }

        } break;

        case STATE_MAINTAIN_BREW:

        {

            // Write text to OLED

            // [ therm : ready to brew ]

            // [ 30 => 120 C           ]

            // Button handler

            if(GPIO_ReadInputDataBit(SW_BTN)) {

                state = STATE_IDLE;

            }

            // Event Handler

            // N/A

        } break;

        case STATE_PREHEAT_STEAM:

        {

            // Write text to OLED

            // [ therm : preheating steam ]

            // [ 30 => 120 C           ]

            // Button handler

            if(GPIO_ReadInputDataBit(SW_BTN)) {

                state = STATE_IDLE;

            }

            // Event Handler

            if(temp >= setpoint) {

                state = STATE_MAINTAIN_STEAM;

            }

        } break;

        case STATE_MAINTAIN_STEAM:

        {

            // Write text to OLED

            // [ therm : ready to steam ]

            // [ 30 => 120 C            ]