Changeset - 4e72955028d8
Parent rev.
Child rev.
[Not reviewed]
default
0 2 0
Ethan Zonca - 10 years ago 2014-07-10 19:47:46
ez@ethanzonca.com
Added LED defs
2 files changed with 11 insertions and 16 deletions:
libraries/oleddrv/bsp.h
1
4
main.c
10
12
0 comments (0 inline, 0 general)
libraries/oleddrv/bsp.h
➞
Show inline comments
 
#ifndef BSP_H
 
#define BSP_H
 
 
/**
 
  IO Connection map
 
 
       SSD1303
 
  Vcc   1  2  Gnd
 
D1/Data 3  4  D0/Clk
 
    D3  5  6  D2
 
    D5  7  8  D4
 
    D7  9 10  D6
 
    WR 11 12  RD
 
   RES 13 14  A0  (1-data,0-command)
 
   CS  15 16  C86 (1-8080, 0-SPI)
 
 
       STM32
 
  D0/Clk    PB13/SPI2 Clk
 
  D1/Data   PB15/SPI2 MOSI
 
  RES       PB12
 
  A0        PB14
 
  CS        Gnd
 
  D2~D7     (Float)
 
  WR        (Float)
 
  RD        (Float)
 
 */
 
 
#define   SSD_Clk         GPIOA,GPIO_Pin_5
 
#define   SSD_Data        GPIOA,GPIO_Pin_7
 
#define   SSD_Reset       GPIOB,GPIO_Pin_2
 
#define   SSD_A0          GPIOB,GPIO_Pin_10
 
#define   SSD_CS          GPIOB,GPIO_Pin_1
 
 
#define   SSD_Clk_Low()     GPIOA->BRR = GPIO_Pin_5
 
#define   SSD_Clk_High()    GPIOA->ODR |= GPIO_Pin_5
 
#define   SSD_Data_Low()    GPIOA->BRR = GPIO_Pin_7
 
#define   SSD_Data_High()   GPIOA->ODR |= GPIO_Pin_7
 
#define   SSD_Reset_Low()   GPIOB->BRR = GPIO_Pin_2
 
#define   SSD_Reset_High()  GPIOB->ODR |= GPIO_Pin_2
 
#define   SSD_A0_Low()      GPIOB->BRR = GPIO_Pin_10
 
#define   SSD_A0_High()     GPIOB->ODR |= GPIO_Pin_10
 
#define   SSD_CS_Low()      GPIOB->BRR = GPIO_Pin_1
 
#define   SSD_CS_High()     GPIOB->ODR |= GPIO_Pin_1
 
 
// Use stdperiph
 
#define   SPI_SendByte(data)  SPI_I2S_SendData(SPI1, data);  //SPI1->DR = (data)
 
#define   SPI_Wait()           while(!(SPI1->SR&SPI_I2S_FLAG_TXE));while(SPI1->SR&SPI_I2S_FLAG_BSY);
 
 
#define   SSD1303_FPS                   50
 
 
#define   SPI_Wait()           while(!(SPI1->SR&SPI_I2S_FLAG_TXE));while(SPI1->SR&SPI_I2S_FLAG_BSY); #define   SSD1303_FPS                   50
 
#define   IsLedOn()       (!(GPIOA->ODR & GPIO_Pin_8))
 
#define   LED_ON()        GPIOA->BRR = GPIO_Pin_8
 
#define   LED_OFF()       GPIOA->BSRR = GPIO_Pin_8
 
#define   ToggleLED()     if(GPIOA->ODR & GPIO_Pin_8){GPIOA->BRR = GPIO_Pin_8;}\
 
                          else{GPIOA->BSRR = GPIO_Pin_8;}
 
#define   GSel1_High()    GPIOB->BSRR = GPIO_Pin_9
 
#define   GSel1_Low()     GPIOB->BRR = GPIO_Pin_9
 
 
#define   MMA_SLEEP()     GPIOB->BRR = GPIO_Pin_11
 
#define   MMA_WAKEUP()    GPIOB->BSRR = GPIO_Pin_11
 
#define   Is_MMA_WAKEUP() (GPIOB->ODR & GPIO_Pin_11)
 
 
#define   DMA_SSD_1303    DMA1_Channel5
 
#define   DMA_Handler_SSD_1303    DMA1_Channel5_IRQHandler
 
 
 
#define   Is_Enc_Key_Down()    (!(GPIOA->IDR & GPIO_Pin_0))
 
 
#endif
main.c
➞
Show inline comments
 
#include "main.h"
 
#include "stm32l100c_discovery.h"
 
#include "ssd1306.h"
 
 
#define LED_POWER GPIOB,  GPIO_Pin_9
 
#define LED_STAT  GPIOA,  GPIO_Pin_15
 
 
static __IO uint32_t TimingDelay;
 
uint8_t BlinkSpeed = 0;
 
 
void init_gpio();
 
void init_spi();
 
 
/* Main */
 
int main(void)
 
{
 
 
   // Hopefully init clocks
 
   SystemInit();
 
   RCC_ClocksTypeDef RCC_Clocks;
 
 
  /* Configure LED3 and LED4 on STM32L100C-Discovery */
 
  STM_EVAL_LEDInit(LED3);
 
  STM_EVAL_LEDInit(LED4);
 
 
 
//  RCC_Configuration();
 
  /* Initialize User_Button on STM32L100C-Discovery */
 
  //STM_EVAL_PBInit(BUTTON_USER, BUTTON_MODE_GPIO);
 
 
  /* SysTick end of count event each 1ms */
 
  RCC_GetClocksFreq(&RCC_Clocks);
 
  SysTick_Config(RCC_Clocks.HCLK_Frequency / 1000);
 
 
 /* Initiate Blink Speed variable */
 
  BlinkSpeed = 1;
 
 
//  while(1) {
 
//	  ITM_SendChar('!');
 
//  }
 
 
 
  init_spi();
 
  //SPI_I2S_SendData(SPI1, 0x1);
 
 /* Init lcd driver */
 
//  SSD1303_Init();
 
//  SSD1303_DrawPoint(3,3,1);
 
//  SSD1303_DrawPoint(5,5,0);
 
 
 
//testme
 
//  GPIO_SetBits(LED_PWR);
 
  STM_EVAL_LEDOn(LED4);
 
  Delay(1000);
 
  STM_EVAL_LEDOff(LED4);
 
// GPIO_ResetBits(LED_PWR);
 
STM_EVAL_LEDOff(LED4);
 
  Delay(1000);
 
 
  while(1)
 
  {
 
      /* Turn on LD4 Blue LED during 1s each time User button is pressed */
 
      STM_EVAL_LEDOn(LED4);
 
      //STM_EVAL_LEDOn(LED3);
 
 
      /* wait for 1s */
 
      Delay(300);
 
 
      /* Turn off LD4 Blue LED after 1s each time User button is pressed */
 
      STM_EVAL_LEDOff(LED4);
 
      Delay(300);
 
  }
 
}
 
 
/**
 
  * @brief  Inserts a delay time.
 
  * @param  nTime: specifies the delay time length, in 1 ms.
 
  * @retval None
 
  */
 
void Delay(__IO uint32_t nTime)
 
{
 
  TimingDelay = nTime;
 
 
  while(TimingDelay != 0);
 
}
 
 
/**
 
  * @brief  Decrements the TimingDelay variable.
 
  * @param  None
 
  * @retval None
 
  */
 
void TimingDelay_Decrement(void)
 
{
 
  if (TimingDelay != 0x00)
 
  {
 
    TimingDelay--;
 
  }
 
}
 
 
 
 
void init_spi(void) {
 
	SPI_InitTypeDef  SPI_InitStructure;
 
 
	// OLED IC
 
	SPI_InitStructure.SPI_Direction = SPI_Direction_1Line_Tx;
 
	SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
 
	SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b;
 
	SPI_InitStructure.SPI_CPOL = SPI_CPOL_High;
 
	SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge;
 
	SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;
 
	SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_64;
 
	SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;
 
	SPI_InitStructure.SPI_CRCPolynomial = 7;
 
	SPI_Init(SPI1, &SPI_InitStructure);
 
	SPI_Cmd(SPI1, ENABLE);           /* Enable the SPI  */
 
 
	// MAX IC
 
	SPI_InitStructure.SPI_Direction = SPI_Direction_1Line_Rx;
 
	SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
 
	SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b;
 
	SPI_InitStructure.SPI_CPOL = SPI_CPOL_High;
 
	SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge;
 
	SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;
 
	SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_64;
 
	SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;
 
	SPI_InitStructure.SPI_CRCPolynomial = 7;
 
	SPI_Init(SPI2, &SPI_InitStructure);
 
	SPI_Cmd(SPI2, ENABLE);           /* Enable the SPI */
 
}
 
 
void init_gpio(void) {
 
 
 GPIO_InitTypeDef GPIO_InitStruct;
 
 
  /** Configure pins as
 
        * Analog
 
        * Input
 
        * Output
 
        * EVENT_OUT
 
        * EXTI
 
  */
 
 
  /*Enable or disable the AHB peripheral clock */
 
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOC|RCC_AHBPeriph_GPIOB|RCC_AHBPeriph_GPIOA|RCC_APB1Periph_SPI2|RCC_APB2Periph_SPI1, ENABLE);
 
 
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE); // EMZ TODO get the right ones
 
 
  /*Configure GPIO pin : PC */
 
  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_13;
 
  GPIO_InitStruct.GPIO_Mode = GPIO_Mode_OUT;
 
  GPIO_InitStruct.GPIO_OType = GPIO_OType_PP;
 
  GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL;
 
  GPIO_InitStruct.GPIO_Speed = GPIO_Speed_400KHz;
 
  GPIO_Init(GPIOC, &GPIO_InitStruct);
 
 
  /*Configure GPIO pin : PB */
 
  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_10|GPIO_Pin_12
 
                          |GPIO_Pin_9;
 
  GPIO_InitStruct.GPIO_Mode = GPIO_Mode_OUT;
 
  GPIO_InitStruct.GPIO_OType = GPIO_OType_PP;
 
  GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL;
 
  GPIO_InitStruct.GPIO_Speed = GPIO_Speed_400KHz;
 
  GPIO_Init(GPIOB, &GPIO_InitStruct);
 
 
  /*Configure GPIO pin : PA */
 
  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_15;
 
  GPIO_InitStruct.GPIO_Mode = GPIO_Mode_OUT;
 
  GPIO_InitStruct.GPIO_OType = GPIO_OType_PP;
 
  GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL;
 
  GPIO_InitStruct.GPIO_Speed = GPIO_Speed_400KHz;
 
  GPIO_Init(GPIOA, &GPIO_InitStruct);
 
 
  /*Configure GPIO pin : PB */
 
  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5|GPIO_Pin_6
 
                          |GPIO_Pin_7;
 
  GPIO_InitStruct.GPIO_Mode = GPIO_Mode_IN;
 
  GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL;
 
  GPIO_Init(GPIOB, &GPIO_InitStruct);
 
 
  /** SPI1 GPIO Configuration
 
  PA5   ------> SPI1_SCK
 
  PA7   ------> SPI1_MOSI
 
  */
 
 
  /*Enable or disable the AHB peripheral clock */
 
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);
 
 
  /*Configure GPIO pin : PA */
 
  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_5|GPIO_Pin_7;
 
  GPIO_InitStruct.GPIO_OType = GPIO_OType_PP;
 
  GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL;
 
  GPIO_InitStruct.GPIO_Speed = GPIO_Speed_400KHz;
 
  GPIO_Init(GPIOA, &GPIO_InitStruct);
 
 
  /*Configure GPIO pin alternate function */
 
  GPIO_PinAFConfig(GPIOA, GPIO_PinSource5, GPIO_AF_SPI1);
 
 
  /*Configure GPIO pin alternate function */
 
  GPIO_PinAFConfig(GPIOA, GPIO_PinSource7, GPIO_AF_SPI1);
 
 
  /** SPI2 GPIO Configuration
 
  PB13   ------> SPI2_SCK
 
  PB14   ------> SPI2_MISO
 
  PB15   ------> SPI2_MOSI
 
  */
 
 
  /*Enable or disable the AHB peripheral clock */
 
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOB, ENABLE);
 
 
  /*Configure GPIO pin : PB */
 
  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_13|GPIO_Pin_14|GPIO_Pin_15;
 
  GPIO_InitStruct.GPIO_OType = GPIO_OType_PP;
 
  GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL;
 
  GPIO_InitStruct.GPIO_Speed = GPIO_Speed_400KHz;
 
  GPIO_Init(GPIOB, &GPIO_InitStruct);
 
 
  /*Configure GPIO pin alternate function */
 
  GPIO_PinAFConfig(GPIOB, GPIO_PinSource13, GPIO_AF_SPI2);
 
 
  /*Configure GPIO pin alternate function */
 
  GPIO_PinAFConfig(GPIOB, GPIO_PinSource14, GPIO_AF_SPI2);
 
 
  /*Configure GPIO pin alternate function */
 
  GPIO_PinAFConfig(GPIOB, GPIO_PinSource15, GPIO_AF_SPI2);
 
 
  /** USB GPIO Configuration
 
  PA11   ------> USB_DM
 
  PA12   ------> USB_DP
 
  */
 
 
  /*Enable or disable the AHB peripheral clock */
 
  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);
 
 
  /*Configure GPIO pin : PA */
 
  GPIO_InitStruct.GPIO_Pin = GPIO_Pin_11|GPIO_Pin_12;
 
  GPIO_InitStruct.GPIO_OType = GPIO_OType_PP;
 
  GPIO_InitStruct.GPIO_PuPd = GPIO_PuPd_NOPULL;
 
  GPIO_InitStruct.GPIO_Speed = GPIO_Speed_400KHz;
 
  GPIO_Init(GPIOA, &GPIO_InitStruct);
 
}
 
 
 
 
 
 
#ifdef  USE_FULL_ASSERT
 
 
/**
 
  * @brief  Reports the name of the source file and the source line number
 
  *   where the assert_param error has occurred.
 
  * @param  file: pointer to the source file name
 
  * @param  line: assert_param error line source number
 
  * @retval None
 
  */
 
void assert_failed(uint8_t* file, uint32_t line)
 
{
 
  /* User can add his own implementation to report the file name and line number,
 
     ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
 
 
  /* Infinite loop */
 
  while (1)
 
  {}
 
}
 
#endif
 
0 comments (0 inline, 0 general)
Server instance: zserverv-1627831 This site is powered by Kallithea, which is © 2010–2021 by various authors & licensed under GPLv3. – Support