//power-percent is 0-1000

            ssr_output = power_percent; //(((uint32_t)SSR_PERIOD * (uint32_t)10 * (uint32_t)100) * power_percent) / (uint32_t)1000000;

        }

        else 

        {

            ssr_output = 0;

        }

        // Only support heating (ssr_output > 0) right now

        if(ssr_output > 0) {

            char tempstr[6];

            itoa(ssr_output, tempstr);

            ssd1306_DrawString("#=", 2, 45);

            ssd1306_DrawString("    ", 2, 57);

            ssd1306_DrawString(tempstr, 2, 57);

            GPIO_SetBits(LED_STAT);

            GPIO_SetBits(SSR_PIN);

            last_ssr_on = ticks;

        }

    }

    // Kill SSR after elapsed period less than SSR_PERIOD 

    if(ticks - last_ssr_on > ssr_output || ssr_output == 0)

    {

        GPIO_ResetBits(LED_STAT);

        GPIO_ResetBits(SSR_PIN);

    }

}

void draw_setpoint() {

    char tempstr[3];

    itoa_fp(temp, temp_frac, tempstr);

    //ssd1306_DrawString("        ", 3, 40);

    ssd1306_DrawString(tempstr, 3, 40);

    ssd1306_DrawString("-> ", 3, 80);

    itoa(setpoint, tempstr);

    ssd1306_DrawString("    ", 3, 95);

    ssd1306_DrawString(tempstr, 3, 95);

}

uint8_t goto_mode = 2;

// State machine

uint8_t sw_btn_last = 0;

uint8_t sw_up_last = 0;

uint8_t sw_down_last = 0;

uint8_t sw_left_last = 0;

uint8_t sw_right_last = 0;

#define SW_BTN_PRESSED (sw_btn_last == 0 && sw_btn == 1) // rising edge on buttonpress

#define SW_UP_PRESSED (sw_up_last == 0 && sw_up == 1)

#define SW_DOWN_PRESSED (sw_down_last == 0 && sw_down == 1)

#define SW_LEFT_PRESSED (sw_left_last == 0 && sw_left == 1)

#define SW_RIGHT_PRESSED (sw_right_last == 0 && sw_right == 1)

/*

 * uint8_t boottobrew = 0;

#define WINDUP_GUARD_GAIN 100

uint16_t windup_guard = WINDUP_GUARD_GAIN;

uint16_t k_p = 1;

uint16_t k_i = 1;

uint16_t k_d = 1;*/

#define EEPROM_ADDR_WINDUP_GUARD 	0x001C

#define EEPROM_ADDR_BOOTTOBREW		0x0020

#define EEPROM_ADDR_K_P			0x0024

#define EEPROM_ADDR_K_I			0x0028

#define EEPROM_ADDR_K_D			0x002C

#define EEPROM_ADDR_BREWTEMP		0x0030

#define EEPROM_ADDR_STEAMTEMP		0x0034

#define EEPROM_BASE_ADDR    0x08080000    

#define EEPROM_BYTE_SIZE    0x0FFF  

/*

uint32_t EEPROM_ReadWord(uint16_t Addr)  

{  

    uint32 *wAddr;  

    wAddr=(uint32 *)(EEPROM_BASE_ADDR+Addr);  

    uint32 res;

    res = *wAddr++;

    while(Length--){  

        *Buffer++=*wAddr++;  

    }     

} 

*/

void save_settings()

{

    DATA_EEPROM_Unlock();

    // Try programming a word at an address divisible by 4

    DATA_EEPROM_Lock();

}

void save_setpoints()

{

    DATA_EEPROM_Unlock();

    DATA_EEPROM_Lock();

}

// TODO: Save/restore temperature setpoint settings

void restore_settings()

{

    DATA_EEPROM_Unlock();

    while(FLASH_GetStatus()==FLASH_BUSY);

    while(FLASH_GetStatus()==FLASH_BUSY);

    while(FLASH_GetStatus()==FLASH_BUSY);

    while(FLASH_GetStatus()==FLASH_BUSY);

    while(FLASH_GetStatus()==FLASH_BUSY);

    while(FLASH_GetStatus()==FLASH_BUSY);

    while(FLASH_GetStatus()==FLASH_BUSY);

    DATA_EEPROM_Lock();

}

void user_input(uint16_t* to_modify)

{

    if(CHANGE_ELAPSED) {

        // TODO: Make function that takes reference to a var and increase/decreases it based on buttonpress

        if(!GPIO_ReadInputDataBit(SW_UP) ) {

            CHANGE_RESET;

            (*to_modify)++;

        }

        else if(!GPIO_ReadInputDataBit(SW_DOWN) && (*to_modify) > 0) {

            CHANGE_RESET;

            (*to_modify)--;

        }

    }

}

void machine()

{

    uint8_t last_state = state;

    uint8_t sw_btn = !GPIO_ReadInputDataBit(SW_BTN);

    uint8_t sw_up = !GPIO_ReadInputDataBit(SW_UP);

    uint8_t sw_down = !GPIO_ReadInputDataBit(SW_DOWN);

    uint8_t sw_left = !GPIO_ReadInputDataBit(SW_LEFT);

    uint8_t sw_right = !GPIO_ReadInputDataBit(SW_RIGHT);

    switch(state)

    {

        // Idle state

        case STATE_IDLE:

        {

            // Write text to OLED

            // [ therm :: idle ]

            ssd1306_DrawString("therm :: idle ", 0, 40);

            pid_enabled = 0;

            char tempstr[6];

            itoa_fp(temp, temp_frac, tempstr);

            ssd1306_DrawString("Temp: ", 3, 40);

            ssd1306_DrawString("    ", 3, 72);

            ssd1306_DrawString(tempstr, 3, 72);

            ssd1306_drawlogo();

            switch(goto_mode) {

                case 2:

                {

                    ssd1306_DrawString("-> brew     ", 1, 40);

                } break;

                case 1:

                {

                    ssd1306_DrawString("-> setup    ", 1, 40);

                } break;

                case 0:

                {

                    ssd1306_DrawString("-> reset    ", 1, 40);

                } break;

            }

            // Button handler

            if(SW_BTN_PRESSED) {

                switch(goto_mode) {

                    case 2:

                        state = STATE_PREHEAT_BREW;

                        break;

                    case 1:

                        state = STATE_SETP;

                        break;

                    case 0:

                        state = STATE_IDLE;

                        break;

                    default:

                        state = STATE_PREHEAT_BREW;

                }

            }

            else if(SW_UP_PRESSED && goto_mode < 2) {

                goto_mode++;

            }

            else if(SW_DOWN_PRESSED && k_p > 0 && goto_mode > 0) {

                goto_mode--;

            }

            // Event Handler

            // N/A