}

void update_temp() {

    // Assert CS

    HAL_GPIO_WritePin(MAX_CS, 0);

    uint8_t rxdatah[1] = {0x00};

    uint8_t rxdatal[1] = {0x00};

    HAL_SPI_Receive(&hspi1, rxdatah, 1, 100);

    HAL_SPI_Receive(&hspi1, rxdatal, 1, 100);

    // Release CS

    HAL_GPIO_WritePin(MAX_CS, 1);

    // Assemble data array into one var

    uint16_t temp_pre = rxdatal[0] | (rxdatah[0]<<8);

    if(temp_pre & 0b0000000000000010) {

        ssd1306_clearscreen();

        //ssd1306_DrawString("Fatal Error", 3, 35);

        HAL_Delay(100);

        status.state = STATE_TC_ERROR;

        status.temp = 0;

        status.temp_frac = 0;

    }

    else if(temp_pre & 0b0000000000000001 && !set.ignore_tc_error) {

        status.state_resume = status.state;

        status.state = STATE_TC_ERROR;

        status.temp = 0;

        status.temp_frac = 0;

    }

    else 

    {

        if(status.state == STATE_TC_ERROR)

        {

            status.state = status.state_resume;

            ssd1306_clearscreen();

        }

        uint8_t sign = status.temp >> 15;// top bit is sign

        temp_pre = temp_pre >> 2; // Drop 2 lowest bits

        status.temp_frac = temp_pre & 0b11; // get fractional part

        status.temp_frac *= 25; // each bit is .25 a degree, up to fixed point

        temp_pre = temp_pre >> 2; // Drop 2 fractional bits 

        int8_t signint;

        if(sign) {

            signint = -1;

        }

        else {

            signint = 1;

        }

        // Convert to Fahrenheit

        if(set.temp_units == TEMP_UNITS_FAHRENHEIT)

        {

            status.temp = signint * ((temp_pre*100) + status.temp_frac);

            status.temp = status.temp * 1.8;

            status.temp += 3200;

            status.temp_frac = status.temp % 100;

            status.temp /= 100;

        }

        // Use Celsius values

        else

        {

            status.temp = temp_pre * signint;

        }

    }

}

// PID implementation

// TODO: Make struct that has the last_temp and i_state in it, pass by ref. Make struct that has other input values maybe.

int16_t last_pid_temp = 0;

uint8_t last_pid_temp_frac = 0;

int16_t i_state = 0;

int16_t update_pid(uint16_t k_p, uint16_t k_i, uint16_t k_d, int16_t temp, uint8_t temp_frac, int16_t setpoint) 

{

  // Calculate instantaneous error

  int16_t error = (int16_t)setpoint - (int16_t)temp; // TODO: Use fixed point fraction

  // Proportional component

  int16_t p_term = k_p * error;

  // Error accumulator (integrator)

  i_state += error;

  // to prevent the iTerm getting huge despite lots of 

  //  error, we use a "windup guard" 

  // (this happens when the machine is first turned on and

  // it cant help be cold despite its best efforts)

  // not necessary, but this makes windup guard values 

  // relative to the current iGain

  int16_t windup_guard_res = set.windup_guard / k_i;  

  // Calculate integral term with windup guard 

  if (i_state > windup_guard_res) 

    i_state = windup_guard_res;

  else if (i_state < -windup_guard_res) 

    i_state = -windup_guard_res;

  int16_t i_term = k_i * i_state;

  // Calculate differential term (slope since last iteration)

  int16_t d_term = (k_d * (status.temp - last_pid_temp));

  // Save temperature for next iteration

  last_pid_temp = status.temp;

  last_pid_temp_frac = status.temp_frac;

  int16_t result = p_term + i_term - d_term;

  // Put out tenths of percent, 0-1000. 

  if(result > 1000)

    result = 1000;

  else if(result < -1000)

    result = -1000;

  // Return feedback

  return result;

}

uint32_t last_ssr_on = 0;

uint32_t last_vcp_tx = 0;

uint32_t last_led = 0;

int16_t ssr_output = 0; // Duty cycle of ssr, 0 to SSR_PERIOD 

// Process things

void process()

{

    update_temp(); // Read MAX31855

    // TODO: Add calibration offset (linear)

    uint32_t ticks = HAL_GetTick();

    if(ticks - last_led > 400) 

    {

        HAL_GPIO_TogglePin(LED_POWER);

        last_led = ticks;

    }

    // Every 200ms, set the SSR on unless output is 0

    if((ticks - last_ssr_on > SSR_PERIOD))

    {

        if(status.pid_enabled) 

        {

            // Get ssr output for next time

            int16_t power_percent = update_pid(set.k_p, set.k_i, set.k_d, status.temp, status.temp_frac, status.setpoint);

            //power-percent is 0-1000

            ssr_output = power_percent; //(((uint32_t)SSR_PERIOD * (uint32_t)10 * (uint32_t)100) * power_percent) / (uint32_t)1000000;

        }

        else 

        {

            ssr_output = 0;

        }

        // Only support heating (ssr_output > 0) right now

        if(ssr_output > 0) {

            char tempstr[6];

            itoa(ssr_output, tempstr, 10);

            ssd1306_DrawString(tempstr, 0, 90);

            HAL_GPIO_WritePin(SSR_PIN, 1);

            last_ssr_on = ticks;

        }

    }

    // Kill SSR after elapsed period less than SSR_PERIOD 

    if(ticks - last_ssr_on > ssr_output || ssr_output == 0)

    {

        HAL_GPIO_WritePin(SSR_PIN, 0);

    }

    if(ticks - last_vcp_tx > VCP_TX_FREQ)

    {

        // Print temp to cdc

        char tempstr[16];

        itoa_fp(status.temp, status.temp_frac, tempstr);

        uint8_t numlen = strlen(tempstr);

        tempstr[numlen] = '\r';

        tempstr[numlen+1] = '\n';

       // while(CDC_Transmit_FS("\r\n", 2) == USBD_BUSY);

        last_vcp_tx = ticks;

    }

}

void save_settings()

{

/*

   Minimal_EEPROM_Unlock();

    // Try programming a word at an address divisible by 4

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_BOOTTOBREW, boottobrew);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_WINDUP_GUARD, windup_guard);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_P, k_p);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_I, k_i);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_D, k_d);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_UNITS, temp_units);

    Minimal_EEPROM_Lock();

*/

}

void save_setpoints()

{

/*

    Minimal_EEPROM_Unlock();

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_BREWTEMP, setpoint_brew);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_STEAMTEMP, setpoint_steam); 

    Minimal_EEPROM_Lock();

*/

}

// TODO: Make a struct that has all settings in it. Pass by ref to this func in a library.

void restore_settings()

{

/*    Minimal_EEPROM_Unlock();

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    boottobrew = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_BOOTTOBREW));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    windup_guard = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_WINDUP_GUARD));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    k_p = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_P));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    k_i = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_I));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    k_d = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_D));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    setpoint_brew = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_BREWTEMP));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    setpoint_steam = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_STEAMTEMP));    

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    temp_units = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_UNITS));    

    Minimal_EEPROM_Lock(); */

}

// vim:softtabstop=4 shiftwidth=4 expandtab