if(ticks - last_led > 400) 

    {

        HAL_GPIO_TogglePin(LED_POWER);

        last_led = ticks;

    }

    // Every 200ms, set the SSR on unless output is 0

    if((ticks - last_ssr_on > SSR_PERIOD))

    {

        if(status.pid_enabled) 

        {

            // Get ssr output for next time

            int16_t power_percent = update_pid(set.k_p, set.k_i, set.k_d, status.temp, status.temp_frac, status.setpoint);

            //power-percent is 0-1000

            ssr_output = power_percent; //(((uint32_t)SSR_PERIOD * (uint32_t)10 * (uint32_t)100) * power_percent) / (uint32_t)1000000;

        }

        else 

        {

            ssr_output = 0;

        }

        // Only support heating (ssr_output > 0) right now

        if(ssr_output > 0) {

            char tempstr[6];

            itoa(ssr_output, tempstr, 10);

            ssd1306_DrawString(tempstr, 0, 90);

            HAL_GPIO_WritePin(SSR_PIN, 1);

            last_ssr_on = ticks;

        }

    }

    // Kill SSR after elapsed period less than SSR_PERIOD 

    if(ticks - last_ssr_on > ssr_output || ssr_output == 0)

    {

        HAL_GPIO_WritePin(SSR_PIN, 0);

    }

    if(ticks - last_vcp_tx > VCP_TX_FREQ)

    {

        // Print temp to cdc

        char tempstr[16];

        itoa_fp(status.temp, status.temp_frac, tempstr);

        uint8_t numlen = strlen(tempstr);

        tempstr[numlen] = '\r';

        tempstr[numlen+1] = '\n';

       // while(CDC_Transmit_FS("\r\n", 2) == USBD_BUSY);

        last_vcp_tx = ticks;

    }

}

void save_settings()

{

/*

   Minimal_EEPROM_Unlock();

    // Try programming a word at an address divisible by 4

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_BOOTTOBREW, boottobrew);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_WINDUP_GUARD, windup_guard);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_P, k_p);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_I, k_i);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_K_D, k_d);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_UNITS, temp_units);

    Minimal_EEPROM_Lock();

*/

}

void save_setpoints()

{

/*

    Minimal_EEPROM_Unlock();

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_BREWTEMP, setpoint_brew);

    Minimal_EEPROM_ProgramWord(EEPROM_BASE_ADDR + EEPROM_ADDR_STEAMTEMP, setpoint_steam); 

    Minimal_EEPROM_Lock();

*/

}

// TODO: Make a struct that has all settings in it. Pass by ref to this func in a library.

void restore_settings()

{

/*    Minimal_EEPROM_Unlock();

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    boottobrew = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_BOOTTOBREW));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    windup_guard = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_WINDUP_GUARD));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    k_p = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_P));

    while(Minimal_FLASH_GetStatus()==FLASH_BUSY);

    k_i = (*(__IO uint32_t*)(EEPROM_BASE_ADDR + EEPROM_ADDR_K_I));