therm Changeset - 618031ff9252 · protofusion repositories

Changeset - 618031ff9252

Parent rev.

Child rev.

[Not reviewed]

cortex-f0

0 4 0

matthewreed - 9 years ago 2015-12-19 22:47:30

Added Reset menu to Idle screen

4 files changed with 103 insertions and 21 deletions:

config.h

display.c

states.h

system/syslib.c

0 comments (0 inline, 0 general)

config.h

➞

Show inline comments

 #ifndef CONFIG_H
 #define CONFIG_H
 // Temperature sensor type
 //#define MAX31855_TC_SENSOR
 #define MAX31865_RTD_SENSOR
 // Virtual serial port transmit rate
 #define VCP_TX_FREQ 1000
 // Solid-state relay maximum on-time
 #define SSR_PERIOD 200
 // Interval of PID calculations
 #define PID_PERIOD 120
 // Pin settings
 #define LED_POWER GPIOF,GPIO_PIN_0
 #define MAX_CS GPIOA,GPIO_PIN_15
 #define SW_BTN  GPIOB, GPIO_PIN_4
 #define SW_UP   GPIOB, GPIO_PIN_7
 #define SW_DOWN GPIOB, GPIO_PIN_3
 #define SW_LEFT GPIOB, GPIO_PIN_5
 #define SW_RIGHT GPIOB, GPIO_PIN_6
 #define SSR_PIN GPIOA, GPIO_PIN_1
 // Visual niceness
 #define hal_init() HAL_Init()
 // Add bootloader option to top of idle screen menu
 #define BOOTLOADER_SHORTCUT
 #endif
 // vim:softtabstop=4 shiftwidth=4 expandtab

display.c

➞

Show inline comments

 #include "stm32f0xx_hal.h"
 #include "ssd1306.h"
 #include "stringhelpers.h"
 #include "display.h"
 #include "config.h"
 #include "states.h"
 #include "syslib.h"
 #include "flash.h"
 #include "gpio.h"
 #ifdef MAX31865_RTD_SENSOR
 #include "max31865.h"
 #endif
 // Private function prototypes
 static void draw_setpoint(therm_status_t* status);
 // Button transition variables
 static uint8_t sw_btn_last = 0;
 static uint8_t sw_up_last = 0;
 static uint8_t sw_down_last = 0;
 static uint8_t sw_left_last = 0;
 static uint8_t sw_right_last = 0;
 // Buttonpress macros
 #define SW_BTN_PRESSED (sw_btn_last == 0 && sw_btn == 1) // rising edge on buttonpress
 #define SW_UP_PRESSED (sw_up_last == 0 && sw_up == 1)
 #define SW_DOWN_PRESSED (sw_down_last == 0 && sw_down == 1)
 #define SW_LEFT_PRESSED (sw_left_last == 0 && sw_left == 1)
 #define SW_RIGHT_PRESSED (sw_right_last == 0 && sw_right == 1)
 // States
 static uint8_t trigger_drawsetpoint = 1;
 static int16_t last_temp = 21245;
 static uint8_t goto_mode = MODE_HEAT;
 static uint8_t reset_mode = RESET_RESET;
 // Display state machine
 void display_process(therm_settings_t* set, therm_status_t* status)
+{
     uint8_t last_state = status->state;
     uint8_t temp_changed = status->temp != last_temp;
     last_temp = status->temp;
     uint8_t sw_btn = !HAL_GPIO_ReadPin(SW_BTN);
     uint8_t sw_up = !HAL_GPIO_ReadPin(SW_UP);
     uint8_t sw_down = !HAL_GPIO_ReadPin(SW_DOWN);
     uint8_t sw_left = !HAL_GPIO_ReadPin(SW_LEFT);
     uint8_t sw_right = !HAL_GPIO_ReadPin(SW_RIGHT);
     switch(status->state)
+    {
         // Idle state
         case STATE_IDLE:
+        {
             // Write text to OLED
             // [ therm :: idle ]
             ssd1306_drawstring("therm :: idle ", 0, 40);
             status->pid_enabled = 0;
             if(temp_changed) {
                 char tempstr[6];
                 itoa_fp(status->temp, status->temp_frac, tempstr);
                 ssd1306_drawstring("Temp: ", 3, 40);
                 ssd1306_drawstring("    ", 3, 72);
                 ssd1306_drawstring(tempstr, 3, 72);
+            }
             ssd1306_drawlogo();
             switch(goto_mode) {
                 case MODE_BOOTLOADER:
+                {
                     ssd1306_drawstring("-> loader   ", 1, 40);
                 } break;
                 case MODE_HEAT:
+                {
                     ssd1306_drawstring("-> heat     ", 1, 40);
                 } break;
                 case MODE_SETUP:
+                {
                     ssd1306_drawstring("-> setup    ", 1, 40);
                 } break;
                 case MODE_RESET:
+                {
                     ssd1306_drawstring("-> reset    ", 1, 40);
                 } break;
 				#ifdef BOOTLOADER_SHORTCUT
                 case MODE_BOOTLOADER:
+                {
                     ssd1306_drawstring("-> dfu      ", 1, 40);
+                }
 				#endif
+            }
             // Button handler
             if(SW_BTN_PRESSED) {
                 switch(goto_mode) {
                     case MODE_BOOTLOADER:
+                    {
                         ssd1306_clearscreen();
                         ssd1306_drawstring("Bootloader Entered", 0, 0);
                         ssd1306_drawstring("Device won't boot", 2, 0);
                         ssd1306_drawstring("until reflashed!", 3, 0);
                         bootloader_enter(); // Resets into bootloader
                         status->state = STATE_IDLE; // Just in case
                     } break;
                     case MODE_HEAT:
                         status->state = STATE_PREHEAT;
                         break;
                     case MODE_SETUP:
                         status->state = STATE_SETP;
                         break;
                     case MODE_RESET:
                         status->state = STATE_IDLE;
                         //flash_erase();
                         NVIC_SystemReset();
                         status->state = STATE_RESET;
                         reset_mode = RESET_RESET;
                         break;
 					#ifdef BOOTLOADER_SHORTCUT
                     case MODE_BOOTLOADER:
                         ssd1306_clearscreen();
                         ssd1306_drawstring("Bootloader Entered", 0, 0);
                         ssd1306_drawstring("Device won't boot", 2, 0);
                         ssd1306_drawstring("until reflashed!", 3, 0);
                         bootloader_enter(); // Resets into bootloader
                         status->state = STATE_RESET; // Just in case
                         break;
 					#endif
                     default:
                         status->state = STATE_PREHEAT;
+                }
+            }
             else if(SW_DOWN_PRESSED && goto_mode < (MODE_SIZE - 1)) {
                 goto_mode++;
+            }
             else if(SW_UP_PRESSED && goto_mode > 0) {
                 goto_mode--;
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETP:
+        {
             // Write text to OLED
             // [ therm :: set p ]
             // [ p = 12         ]
             ssd1306_drawstring("Proportional", 0, 40);
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->val.k_p, tempstr, 10);
             ssd1306_drawstring("P=", 1, 45);
             ssd1306_drawstring("    ", 1, 57);
             ssd1306_drawstring(tempstr, 1, 57);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETI;
+            }
             else {
                 user_input(&set->val.k_p);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETI:
+        {
             // Write text to OLED
             // [ therm :: set i ]
             // [ i = 12         ]
             ssd1306_drawstring("Integral", 0, 40);
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->val.k_i, tempstr, 10);
             ssd1306_drawstring("I=", 1, 45);
             ssd1306_drawstring("    ", 1, 57);
             ssd1306_drawstring(tempstr, 1, 57);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETD;
+            }
             else {
                 user_input(&set->val.k_i);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETD:
+        {
             // Write text to OLED
             // [ therm :: set d ]
             // [ d = 12         ]
             ssd1306_drawstring("Derivative", 0, 40);
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->val.k_d, tempstr, 10);
             ssd1306_drawstring("D=", 1, 45);
             ssd1306_drawstring("    ", 1, 57);
             ssd1306_drawstring(tempstr, 1, 57);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETWINDUP;
+            }
             else {
                 user_input(&set->val.k_d);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETWINDUP:
+        {
             // Write text to OLED
             // [ therm :: set windup ]
             // [ g = 12         ]
             ssd1306_drawstring("Windup Guard", 0, 40);
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->val.windup_guard, tempstr, 10);
             ssd1306_drawstring("G=", 1, 45);
             ssd1306_drawstring("    ", 1, 57);
             ssd1306_drawstring(tempstr, 1, 57);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETBOOTTOBREW;
+            }
             else {
                 user_input(&set->val.windup_guard);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETBOOTTOBREW:
+        {
             // Write text to OLED
             // [ therm :: set windup ]
             // [ g = 12         ]
             ssd1306_drawstring("Start on Boot", 0, 40);
             ssd1306_drawlogo();
             ssd1306_drawstring("sob=", 1, 45);
             if(set->val.boottobrew)
                 ssd1306_drawstring("Enabled ", 1, 70);
             else
                 ssd1306_drawstring("Disabled", 1, 70);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETUNITS;
+            }
             else if(!HAL_GPIO_ReadPin(SW_UP)) {
                 set->val.boottobrew = 1;
+            }
             else if(!HAL_GPIO_ReadPin(SW_DOWN)) {
                 set->val.boottobrew = 0;
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETUNITS:
+        {
             // Write text to OLED
             // [ therm :: set windup ]
             // [ g = 12         ]
             ssd1306_drawstring("Units: ", 0, 40);
             ssd1306_drawlogo();
             if(set->val.temp_units == TEMP_UNITS_FAHRENHEIT)
                 ssd1306_drawstring("Fahrenheit", 1, 60);
             else
                 ssd1306_drawstring("Celsius   ", 1, 60);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETTEMPOFFSET;
+            }
             else if(!HAL_GPIO_ReadPin(SW_UP)) {
                 set->val.temp_units = TEMP_UNITS_FAHRENHEIT;
+            }
             else if(!HAL_GPIO_ReadPin(SW_DOWN)) {
                 set->val.temp_units = TEMP_UNITS_CELSIUS;
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETTEMPOFFSET:
+        {
             // Write text to OLED
             // [ therm :: set temp offset ]
             // [ g = 12         ]
             ssd1306_drawstring("Temp Cal Offset", 0, 40);
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->val.temp_offset, tempstr, 10);
             ssd1306_drawstring("O=", 1, 45);
             ssd1306_drawstring("    ", 1, 57);
             ssd1306_drawstring(tempstr, 1, 57);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 flash_save(&set);
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input_signed(&set->val.temp_offset);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_PREHEAT:
+        {
             // Write text to OLED
             // [ therm : preheating brew ]
             // [ 30 => 120 C             ]
             ssd1306_drawstring("Preheating...", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->val.setpoint_brew;
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input(&set->val.setpoint_brew);
+            }
             // Event Handler
             if(status->temp >= status->setpoint) {
                 status->state = STATE_MAINTAIN;
+            }
         } break;
         case STATE_MAINTAIN:
+        {
             // Write text to OLED
             // [ therm : ready to brew ]
             // [ 30 => 120 C           ]
             ssd1306_drawstring("Preheated!", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->val.setpoint_brew;
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input(&set->val.setpoint_brew);
+            }
             // Event Handler
             // N/A
         } break;
         // Thermocouple error
         case STATE_TC_ERROR:
+        {
             // Write text to OLED
             // [ therm : ready to steam ]
             // [ 30 => 120 C            ]
             ssd1306_drawstring("Error:              ", 0, 0);
             char tempstr[6];
             itoa(status->error_code, tempstr, 10);
             ssd1306_drawstring(tempstr, 0, 57);
             //TODO: add RTD error codes
             if(status->error_code == 1)
                 ssd1306_drawstring("    TC Open Circuit", 1, 0);
             else if(status->error_code == 4)
                 ssd1306_drawstring("    TC Short to GND", 1, 0);
             else if(status->error_code == 8)
                 ssd1306_drawstring("    TC Short to VCC", 1, 0);
             else
                 ssd1306_drawstring("#?, Unknown Error", 1, 0);
             ssd1306_drawstring("                    ", 2, 0);
             ssd1306_drawstring("-> to ignore all or", 2, 0);
             ssd1306_drawstring("press to continue", 3, 0);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
 				#ifdef MAX31865_RTD_SENSOR
 				max31865_clear_errors(spi_get());
 				#endif
+            }
             else if(SW_RIGHT_PRESSED) {
                 set->val.ignore_error = 1;
                 status->state = STATE_IDLE;
+            }
             // Event Handler
             // Maybe handle if TC is plugged in
             // N/A
         } break;
         // Reset state
         case STATE_RESET:
+        {
             // Write text to OLED
             // [ therm :: reset ]
             ssd1306_drawstring("therm :: reset ", 0, 40);
             status->pid_enabled = 0;
             ssd1306_drawlogo();
             switch(reset_mode) {
 				case RESET_RESET:
+				{
 					ssd1306_drawstring("-> reset     ", 1, 40);
 				} break;
                 case RESET_BOOTLOADER:
+                {
                     ssd1306_drawstring("-> bootloader", 1, 40);
                 } break;
                 case RESET_EXIT:
+                {
                     ssd1306_drawstring("-> exit      ", 1, 40);
                 } break;
+            }
             // Button handler
             if(SW_BTN_PRESSED) {
                 switch(reset_mode) {
                     case RESET_BOOTLOADER:
+                    {
                         ssd1306_clearscreen();
                         ssd1306_drawstring("Bootloader Entered", 0, 0);
                         ssd1306_drawstring("Device won't boot", 2, 0);
                         ssd1306_drawstring("until reflashed!", 3, 0);
                         HAL_Delay(1000);
                         bootloader_enter(); // Resets into bootloader
                         status->state = STATE_RESET; // Just in case
                     } break;
                     case RESET_RESET:
+                    {
                         status->state = STATE_RESET;
                         //flash_erase();
                         NVIC_SystemReset();
                     } break;
                     case RESET_EXIT:
+                    {
                         status->state = STATE_IDLE;
                     } break;
+                }
+            }
             else if(SW_DOWN_PRESSED && reset_mode < (RESET_SIZE-1)) {
                 reset_mode++;
+            }
             else if(SW_UP_PRESSED && reset_mode > 0) {
                 reset_mode--;
+            }
             // Event Handler
             // N/A
         } break;
         // Something is terribly wrong
         default:
+        {
             status->state = STATE_IDLE;
             status->pid_enabled = 0;
         } break;
+    }
     if(last_state != status->state) {
         // Clear screen on state change
         goto_mode = MODE_HEAT;
         trigger_drawsetpoint = 1;
         ssd1306_clearscreen();
+    }
     // Last buttonpress
     sw_btn_last = sw_btn;
     sw_up_last = sw_up;
     sw_down_last = sw_down;
     sw_left_last = sw_left;
     sw_right_last = sw_right;
+}
 static int32_t temp_last = 43002;
 static int32_t setpoint_last = 10023;
 // Draw current setpoint on display
 static void draw_setpoint(therm_status_t* status) {
     // FIXME: need to do this when switching modes too
     if(status->temp != temp_last || trigger_drawsetpoint) {
         char tempstr[3];
         itoa_fp(status->temp, status->temp_frac, tempstr);
         ssd1306_drawstringbig("      ", 3, 0);
         ssd1306_drawstringbig(tempstr, 3, 0);
+    }
     if(trigger_drawsetpoint)
         ssd1306_drawstringbig(">", 3, 74);
     if(status->setpoint != setpoint_last || trigger_drawsetpoint) {
         char tempstr[3];
         itoa(status->setpoint, tempstr, 10);
         ssd1306_drawstringbig("   ", 3, 90);
         ssd1306_drawstringbig(tempstr, 3, 90);
+    }
     trigger_drawsetpoint = 0;
     setpoint_last = status->setpoint;
     temp_last = status->temp;
+}
 // vim:softtabstop=4 shiftwidth=4 expandtab

states.h

➞

Show inline comments

 #ifndef STATES_H
 #define STATES_H
 #include "config.h"
 typedef struct {
     int32_t temp;
     uint8_t temp_frac;
     uint8_t state_resume;
     uint8_t state;
     int32_t setpoint;
     uint8_t pid_enabled;
     uint8_t error_code;
 } therm_status_t;
 typedef union
+{
      struct {
         uint32_t boottobrew;
         uint32_t temp_units;
         uint32_t windup_guard;
         uint32_t k_p;
         uint32_t k_i;
         uint32_t k_d;
         int32_t temp_offset;
         uint32_t ignore_error;
         int32_t setpoint_brew;
         int32_t setpoint_steam;
     } val;
     uint16_t data[128];
 } therm_settings_t;
 enum tempunits {
     TEMP_UNITS_CELSIUS = 0,
     TEMP_UNITS_FAHRENHEIT,
 };
 enum state {
     STATE_IDLE = 0,
     STATE_SETP,
     STATE_SETI,
     STATE_SETD,
     STATE_SETSTEPS,
     STATE_SETWINDUP,
     STATE_SETBOOTTOBREW,
     STATE_SETUNITS,
     STATE_SETTEMPOFFSET,
     STATE_PREHEAT,
     STATE_MAINTAIN,
     STATE_TC_ERROR,
 	STATE_RESET,
 };
 enum GOTO_MODE {
 	MODE_HEAT = 0,
 	#ifdef BOOTLOADER_SHORTCUT
 	MODE_BOOTLOADER,
 	#endif
 	MODE_HEAT,
 	MODE_SETUP,
 	MODE_RESET,
 	MODE_BOOTLOADER,
 	MODE_SIZE,
 };
 enum RESET_MODE {
 	RESET_RESET = 0,
 	RESET_BOOTLOADER,
 	RESET_EXIT,
 	RESET_SIZE,
 };
 #endif

system/syslib.c

➞

Show inline comments

 #include "stm32f0xx_hal.h"
 /* Notes:
 Need to have DFU jump right to the program to unset those option bytes, or somehow have dfu-util unset them. Probably try using the :leave parameter...
        Flashing a binary file to address 0x8004000 of device memory and ask the device to leave DFU mode:
          $ dfu-util -a 0 -s 0x08004000:leave -D /path/to/image.bin
 */
 // Unset bootloader option bytes
 void bootloader_unset(void)
+{
     FLASH_OBProgramInitTypeDef OBParam;
     HAL_FLASHEx_OBGetConfig(&OBParam);
     if(OBParam.USERConfig != 0xFF)
+    {
         OBParam.OptionType = OPTIONBYTE_USER;
         OBParam.USERConfig = 0xFF;
         HAL_FLASH_Unlock();
         HAL_FLASH_OB_Unlock();
         HAL_FLASHEx_OBErase();
         HAL_FLASHEx_OBProgram(&OBParam);
         HAL_FLASH_OB_Lock();
         HAL_FLASH_OB_Launch();
+    }
+}
 // See thread: https://my.st.com/public/STe2ecommunities/mcu/Lists/cortex_mx_stm32/Flat.aspx?RootFolder=https%3a%2f%2fmy.st.com%2fpublic%2fSTe2ecommunities%2fmcu%2fLists%2fcortex_mx_stm32%2fJump%20to%20USB%20DFU%20Bootloader%20in%20startup%20code%20on%20STM32F042&FolderCTID=0x01200200770978C69A1141439FE559EB459D7580009C4E14902C3CDE46A77F0FFD06506F5B&currentviews=185
 // Set option bytes to enter bootloader upon reset
 void bootloader_enter(void) {
     FLASH_OBProgramInitTypeDef OBParam;
     HAL_FLASHEx_OBGetConfig(&OBParam);
     // FIXME TODO: CHECK THESE OPTION BYTES, he was using an F1 processor. What about the switch flag?
     OBParam.OptionType = OPTIONBYTE_USER;
     /*Reset NBOOT0 and BOOT_SEL,  see: RM 2.5 Boot configuration*/
     OBParam.USERConfig = 0x77; //Sorry for magic number :)
     HAL_FLASH_Unlock();
     HAL_FLASH_OB_Unlock();
     HAL_FLASHEx_OBErase();
     HAL_FLASHEx_OBProgram(&OBParam);
     HAL_FLASH_OB_Lock();
     HAL_FLASH_Lock();
     HAL_FLASH_OB_Launch();
+}
 // Clock configuration
 void systemclock_init(void)
+{
   RCC_OscInitTypeDef RCC_OscInitStruct;
   RCC_ClkInitTypeDef RCC_ClkInitStruct;
   RCC_PeriphCLKInitTypeDef PeriphClkInit;
   // Enable HSI48 for main system clock
   RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48|RCC_OSCILLATORTYPE_HSI14;
   RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
   RCC_OscInitStruct.HSI14State = RCC_HSI14_ON;
   RCC_OscInitStruct.HSI14CalibrationValue = 16;
   RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
   HAL_RCC_OscConfig(&RCC_OscInitStruct);
   RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK;
   RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI48;
   RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
   RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
   HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
   PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB;
   PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_HSI48;
   HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
   __SYSCFG_CLK_ENABLE();
+}

0 comments (0 inline, 0 general)