therm Changeset - a5edaa5d3c45 · protofusion repositories

Changeset - a5edaa5d3c45

Parent rev.

Child rev.

[Not reviewed]

cortex-f0

0 1 0

Ethan Zonca - 8 years ago 2016-04-23 22:24:38
ez@ethanzonca.com

Fixed preheating message with cooler plant

1 file changed with 5 insertions and 1 deletions:

display.c

0 comments (0 inline, 0 general)

display.c

➞

Show inline comments

@@ @@ -376,97 +376,101 @@ void display_process(therm_settings_t* s @@
                 set->val.temp_units = TEMP_UNITS_FAHRENHEIT;
+            }
             else if(!HAL_GPIO_ReadPin(SW_DOWN)) {
                 set->val.temp_units = TEMP_UNITS_CELSIUS;
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETTEMPOFFSET:
+        {
             // Write text to OLED
             // [ therm :: set temp offset ]
             // [ g = 12         ]
             ssd1306_drawstring("Temp Cal Offset", 0, 40);
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->val.temp_offset, tempstr, 10);
             ssd1306_drawstring("O=", 1, 45);
             ssd1306_drawstring("    ", 1, 57);
             ssd1306_drawstring(tempstr, 1, 57);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 flash_save(set);
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input_signed(&set->val.temp_offset);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_PREHEAT:
+        {
             // Write text to OLED
             // [ therm : preheating brew ]
             // [ 30 => 120 C             ]
             ssd1306_drawstring("Preheating...", 0, 0);
             if(set->val.plant_type == PLANT_HEATER)
                 ssd1306_drawstring("Preheating...", 0, 0);
             else
                 ssd1306_drawstring("Precooling...", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
             status->setpoint = set->val.setpoint_brew;
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input((uint16_t*)&set->val.setpoint_brew);
+            }
             // Event Handler
             if(status->temp >= status->setpoint) {
                 status->state = STATE_MAINTAIN;
+            }
         } break;
         case STATE_MAINTAIN:
+        {
             // Write text to OLED
             // [ therm : ready to brew ]
             // [ 30 => 120 C           ]
             if(set->val.plant_type == PLANT_HEATER)
                 ssd1306_drawstring("Preheated!", 0, 0);
             else
                 ssd1306_drawstring("Precooled!", 0, 0);
             draw_setpoint(status);
             status->pid_enabled = 1;
             status->setpoint = set->val.setpoint_brew;
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input((uint16_t*)&set->val.setpoint_brew);
+            }
             // Event Handler
             // N/A
         } break;

0 comments (0 inline, 0 general)