therm Changeset - db81b1787e6e · protofusion repositories

Changeset - db81b1787e6e

Parent rev.

Child rev.

[Not reviewed]

cortex-f0

0 8 0

matthewreed - 9 years ago 2015-12-23 22:37:10

Cleaned up pid code and several other todos

8 files changed with 66 insertions and 50 deletions:

display.c

display.h

gpio.c

gpio.h

main.c

max31865.c

pid.c

pid.h

0 comments (0 inline, 0 general)

display.c

➞

Show inline comments

@@ @@ -146,425 +146,431 @@ void display_process(therm_settings_t* s @@
             ssd1306_drawstring("    ", 1, 57);
             ssd1306_drawstring(tempstr, 1, 57);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETI;
+            }
             else {
                 user_input((uint16_t*)&set->val.k_p);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETI:
+        {
             // Write text to OLED
             // [ therm :: set i ]
             // [ i = 12         ]
             ssd1306_drawstring("Integral", 0, 40);
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->val.k_i, tempstr, 10);
             ssd1306_drawstring("I=", 1, 45);
             ssd1306_drawstring("    ", 1, 57);
             ssd1306_drawstring(tempstr, 1, 57);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETD;
+            }
             else {
                 user_input((uint16_t*)&set->val.k_i);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETD:
+        {
             // Write text to OLED
             // [ therm :: set d ]
             // [ d = 12         ]
             ssd1306_drawstring("Derivative", 0, 40);
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->val.k_d, tempstr, 10);
             ssd1306_drawstring("D=", 1, 45);
             ssd1306_drawstring("    ", 1, 57);
             ssd1306_drawstring(tempstr, 1, 57);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETWINDUP;
+            }
             else {
                 user_input((uint16_t*)&set->val.k_d);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETWINDUP:
+        {
             // Write text to OLED
             // [ therm :: set windup ]
             // [ g = 12         ]
             ssd1306_drawstring("Windup Guard", 0, 40);
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->val.windup_guard, tempstr, 10);
             ssd1306_drawstring("G=", 1, 45);
             ssd1306_drawstring("    ", 1, 57);
             ssd1306_drawstring(tempstr, 1, 57);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETBOOTTOBREW;
+            }
             else {
                 user_input((uint16_t*)&set->val.windup_guard);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETBOOTTOBREW:
+        {
             // Write text to OLED
             // [ therm :: set windup ]
             // [ g = 12         ]
             ssd1306_drawstring("Start on Boot", 0, 40);
             ssd1306_drawlogo();
             ssd1306_drawstring("sob=", 1, 45);
             if(set->val.boottobrew)
                 ssd1306_drawstring("Enabled ", 1, 70);
             else
                 ssd1306_drawstring("Disabled", 1, 70);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETUNITS;
+            }
             else if(!HAL_GPIO_ReadPin(SW_UP)) {
                 set->val.boottobrew = 1;
+            }
             else if(!HAL_GPIO_ReadPin(SW_DOWN)) {
                 set->val.boottobrew = 0;
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETUNITS:
+        {
             // Write text to OLED
             // [ therm :: set windup ]
             // [ g = 12         ]
             ssd1306_drawstring("Units: ", 0, 40);
             ssd1306_drawlogo();
             if(set->val.temp_units == TEMP_UNITS_FAHRENHEIT)
                 ssd1306_drawstring("Fahrenheit", 1, 60);
             else
                 ssd1306_drawstring("Celsius   ", 1, 60);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETTEMPOFFSET;
+            }
             else if(!HAL_GPIO_ReadPin(SW_UP)) {
                 set->val.temp_units = TEMP_UNITS_FAHRENHEIT;
+            }
             else if(!HAL_GPIO_ReadPin(SW_DOWN)) {
                 set->val.temp_units = TEMP_UNITS_CELSIUS;
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETTEMPOFFSET:
+        {
             // Write text to OLED
             // [ therm :: set temp offset ]
             // [ g = 12         ]
             ssd1306_drawstring("Temp Cal Offset", 0, 40);
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->val.temp_offset, tempstr, 10);
             ssd1306_drawstring("O=", 1, 45);
             ssd1306_drawstring("    ", 1, 57);
             ssd1306_drawstring(tempstr, 1, 57);
             ssd1306_drawstring("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 flash_save(set);
                 status->state = STATE_IDLE;
+            }
             else {
-                user_input_signed((int16_t*)(&set->val.temp_offset));
                 user_input_signed(&set->val.temp_offset);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_PREHEAT:
+        {
             // Write text to OLED
             // [ therm : preheating brew ]
             // [ 30 => 120 C             ]
             ssd1306_drawstring("Preheating...", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->val.setpoint_brew;
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input((uint16_t*)&set->val.setpoint_brew);
+            }
             // Event Handler
             if(status->temp >= status->setpoint) {
                 status->state = STATE_MAINTAIN;
+            }
         } break;
         case STATE_MAINTAIN:
+        {
             // Write text to OLED
             // [ therm : ready to brew ]
             // [ 30 => 120 C           ]
             ssd1306_drawstring("Preheated!", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->val.setpoint_brew;
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input((uint16_t*)&set->val.setpoint_brew);
+            }
             // Event Handler
             // N/A
         } break;
         // Thermocouple error
         case STATE_TC_ERROR:
+        {
             // Write text to OLED
             // [ therm : ready to steam ]
             // [ 30 => 120 C            ]
             ssd1306_drawstring("Error:              ", 0, 0);
             char tempstr[6];
             itoa(status->error_code, tempstr, 10);
             ssd1306_drawstring(tempstr, 0, 57);
             //TODO: add RTD error codes
             if(status->error_code == 1)
                 ssd1306_drawstring("    TC Open Circuit", 1, 0);
             else if(status->error_code == 4)
                 ssd1306_drawstring("    TC Short to GND", 1, 0);
             else if(status->error_code == 8)
                 ssd1306_drawstring("    TC Short to VCC", 1, 0);
             else
                 ssd1306_drawstring("#?, Unknown Error", 1, 0);
             ssd1306_drawstring("                    ", 2, 0);
             ssd1306_drawstring("-> to ignore all or", 2, 0);
             ssd1306_drawstring("press to continue", 3, 0);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
 				#ifdef MAX31865_RTD_SENSOR
 				max31865_clear_errors(spi_get());
 				#endif
+            }
             else if(SW_RIGHT_PRESSED) {
                 set->val.ignore_error = 1;
                 status->state = STATE_IDLE;
+            }
             // Event Handler
             // Maybe handle if TC is plugged in
             // N/A
         } break;
         // Reset state
         case STATE_RESET:
+        {
             // Write text to OLED
             // [ therm :: reset ]
             ssd1306_drawstring("therm :: reset ", 0, 40);
             status->pid_enabled = 0;
             ssd1306_drawlogo();
             switch(reset_mode) {
 				case RESET_DEFAULTS:
+				{
 					ssd1306_drawstring("-> defaults   ", 1, 40);
 				} break;
                 case RESET_BOOTLOADER:
+                {
                     ssd1306_drawstring("-> bootloader ", 1, 40);
                 } break;
                 case RESET_REBOOT:
+                {
                     ssd1306_drawstring("-> reboot     ", 1, 40);
                 } break;
                 case RESET_EXIT:
+                {
                     ssd1306_drawstring("-> exit       ", 1, 40);
                 } break;
+            }
             // Button handler
             if(SW_BTN_PRESSED) {
                 switch(reset_mode) {
                     case RESET_BOOTLOADER:
+                    {
                         ssd1306_clearscreen();
                         ssd1306_drawstring("Bootloader Entered", 0, 0);
                         ssd1306_drawstring("Device won't boot", 2, 0);
                         ssd1306_drawstring("until reflashed!", 3, 0);
                         HAL_Delay(1000);
                         bootloader_enter(); // Resets into bootloader
                         status->state = STATE_RESET; // Just in case
                     } break;
                     case RESET_DEFAULTS:
+                    {
                         status->state = STATE_RESET;
                         flash_load_defaults(set);
                         flash_save(set);
                         NVIC_SystemReset();
                     } break;
                     case RESET_REBOOT:
+                    {
                         status->state = STATE_RESET;
                         NVIC_SystemReset();
                     } break;
                     case RESET_EXIT:
+                    {
                         status->state = STATE_IDLE;
                     } break;
+                }
+            }
             else if(SW_DOWN_PRESSED && reset_mode < (RESET_SIZE-1)) {
                 reset_mode++;
+            }
             else if(SW_UP_PRESSED && reset_mode > 0) {
                 reset_mode--;
+            }
             // Event Handler
             // N/A
         } break;
         // Something is terribly wrong
         default:
+        {
             status->state = STATE_IDLE;
             status->pid_enabled = 0;
         } break;
+    }
     if(last_state != status->state) {
         // Clear screen on state change
         goto_mode = MODE_HEAT;
         trigger_drawsetpoint = 1;
         ssd1306_clearscreen();
+    }
     // Last buttonpress
     sw_btn_last = sw_btn;
     sw_up_last = sw_up;
     sw_down_last = sw_down;
     sw_left_last = sw_left;
     sw_right_last = sw_right;
+}
 static int32_t temp_last = 43002;
 static int32_t setpoint_last = 10023;
 // Draw current setpoint on display
 static void draw_setpoint(therm_status_t* status) {
     // FIXME: need to do this when switching modes too
     if(status->temp != temp_last || trigger_drawsetpoint) {
         char tempstr[3];
         itoa_fp(status->temp, status->temp_frac, tempstr);
         ssd1306_drawstringbig("      ", 3, 0);
         ssd1306_drawstringbig(tempstr, 3, 0);
+    }
     if(trigger_drawsetpoint)
         ssd1306_drawstringbig(">", 3, 74);
     if(status->setpoint != setpoint_last || trigger_drawsetpoint) {
         char tempstr[3];
         itoa(status->setpoint, tempstr, 10);
         ssd1306_drawstringbig("   ", 3, 90);
         ssd1306_drawstringbig(tempstr, 3, 90);
+    }
     trigger_drawsetpoint = 0;
     setpoint_last = status->setpoint;
     temp_last = status->temp;
+}
 void display_startup_screen() {
     ssd1306_clearscreen();
     ssd1306_drawstring("therm v0.2", 1, 40);
     ssd1306_drawstring("protofusion.org/therm", 3, 0);
+}
 // vim:softtabstop=4 shiftwidth=4 expandtab

display.h

➞

Show inline comments

 #ifndef DISPLAY_H
 #define DISPLAY_H
 #include <stdlib.h>
 #include "stm32f0xx_hal.h"
 #include "states.h"
 #include "ssd1306.h"
 #include "stringhelpers.h"
 #include "config.h"
 #include "states.h"
 #include "syslib.h"
 #include "flash.h"
 #include "gpio.h"
 #ifdef MAX31865_RTD_SENSOR
 #include "max31865.h"
 #endif
 void display_startup_screen();
 void display_process(therm_settings_t* set, therm_status_t* status);
 #endif

gpio.c

➞

Show inline comments

 #include "gpio.h"
 // Increase on each press, and increase at a fast rate after duration elapsed of continuously holding down... somehow...
 static uint32_t change_time_reset = 0;
 // Increment/decrement unsigned variable with up/down buttons
 void user_input(uint16_t* to_modify)
+{
     if(CHANGE_ELAPSED) {
         if(!HAL_GPIO_ReadPin(SW_UP) ) {
             CHANGE_RESET;
             (*to_modify)++;
+        }
         else if(!HAL_GPIO_ReadPin(SW_DOWN) && (*to_modify) > 0) {
             CHANGE_RESET;
             (*to_modify)--;
+        }
+    }
+}
 // Increment/decrement signed variable with up/down buttons
-void user_input_signed(int16_t* to_modify)
+void user_input_signed(int32_t* to_modify)
+{
-    // TODO: Bounds check on int16_t
+	//fixme: need to cast to 16/32 bits correctly
     if(CHANGE_ELAPSED) {
         if(!HAL_GPIO_ReadPin(SW_UP) ) {
             CHANGE_RESET;
             if (*to_modify < 32768)
             (*to_modify)++;
+        }
         else if(!HAL_GPIO_ReadPin(SW_DOWN)) {
             CHANGE_RESET;
             if (*to_modify >= -32768)
             (*to_modify)--;
+        }
+    }
+}
 // Initialize GPIO
 void gpio_init(void)
+{
   GPIO_InitTypeDef GPIO_InitStruct;
     /* GPIO Ports Clock Enable */
   __GPIOF_CLK_ENABLE();
   __GPIOA_CLK_ENABLE();
   __GPIOB_CLK_ENABLE();
   __SPI1_CLK_ENABLE();
   //////////////////
   // PORT F       //
   //////////////////
   // PORTF OUTPUT
   // Configure GPIO pin : PF0 [Power LED]
   GPIO_InitStruct.Pin = GPIO_PIN_0;
   GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
   HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
   // PORTF UNUSED
   // Configure GPIO pin : PF1
   GPIO_InitStruct.Pin = GPIO_PIN_1;
   GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
   //////////////////
   // PORT A       //
   //////////////////
   // PORT A OUTPUT
   // Configure GPIO pins : (SSR+ CS_OLED RES D/C CS_MAX)
   GPIO_InitStruct.Pin = GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3|GPIO_PIN_4|GPIO_PIN_15;
   GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
   HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
   // PORTA INPUT
   // Configure GPIO pin : PA15
 //  GPIO_InitStruct.Pin = GPIO_PIN_15;
 //  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
 //  GPIO_InitStruct.Pull = GPIO_PULLUP;
 //  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
   // PORTA UNUSED
   // Configure GPIO pins : PA0 PA8
   GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_8;
   GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
   // USART1 [PORTA]
   // Configure GPIO pins : PA9 PA10
   GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
   GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
   GPIO_InitStruct.Alternate = GPIO_AF1_USART1;
   HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
   // SPI1 [PORTA]
   // Configure GPIO pin : PA, MOSI, SCK
   GPIO_InitStruct.Pin = GPIO_PIN_7|GPIO_PIN_5;
   GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
   GPIO_InitStruct.Alternate = GPIO_AF0_SPI1;
   HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
   // Configure GPIO pin: PA, MISO
   GPIO_InitStruct.Pin = GPIO_PIN_6;
   GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
   GPIO_InitStruct.Alternate = GPIO_AF0_SPI1;
   HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
   // USB [PORTA]
   /** USB GPIO Configuration
   PA11   ------> USB_DM
   PA12   ------> USB_DP
   */
   // Configure GPIO pin : PA, D+, D-
   GPIO_InitStruct.Pin = GPIO_PIN_11|GPIO_PIN_12;
   GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   GPIO_InitStruct.Speed = GPIO_SPEED_HIGH;
   GPIO_InitStruct.Alternate = GPIO_AF2_USB; // Can also be AF5
   HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
   //////////////////
   // PORT B       //
   //////////////////
   // PORT B UNUSED
   // Configure GPIO pins : PB0 PB1 PB8
   GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_8;
   GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
   // PORT B INPUT
   // Configure GPIO pins : PB3 PB4 PB5 PB6 PB7
   GPIO_InitStruct.Pin = GPIO_PIN_3|GPIO_PIN_4|GPIO_PIN_5|GPIO_PIN_6
                           |GPIO_PIN_7;
   GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
   GPIO_InitStruct.Pull = GPIO_PULLUP;
   HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
   // Enable DMA clocks (Is AHB even the right thing???)
   //RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE); // EMZ TODO get the right ones
+}
 // vim:softtabstop=4 shiftwidth=4 expandtab

gpio.h

➞

Show inline comments

 #ifndef GPIO_H
 #define GPIO_H
 #include <inttypes.h>
 #include "stm32f0xx_hal.h"
 #include "stm32f0xx_hal_conf.h"
 #include "config.h"
 #define CHANGE_PERIOD_MS 100
 #define CHANGE_ELAPSED (HAL_GetTick() - change_time_reset) > CHANGE_PERIOD_MS
 #define CHANGE_RESET change_time_reset = HAL_GetTick()
 void user_input(uint16_t* to_modify);
-void user_input_signed(int16_t* to_modify);
+void user_input_signed(int32_t* to_modify);
 void gpio_init(void);
 #endif
 // vim:softtabstop=4 shiftwidth=4 expandtab

main.c

➞

Show inline comments

 #include "stm32f0xx_hal.h"
 #include "config.h"
 #include "syslib.h"
 #include "pid.h"
 #include "states.h"
 #include "ssd1306.h"
 #ifdef MAX31855_TC_SENSOR
 #include "max31855.h"
 #endif
 #ifdef MAX31865_RTD_SENSOR
 #include "max31865.h"
 #else
 #include "max31855.h"
 #endif
 #include "gpio.h"
 #include "spi.h"
 #include "flash.h"
 #include "stringhelpers.h"
 #include "display.h"
 #include "usb_device.h"
 #include "usbd_cdc_if.h"
 therm_settings_t set;
 therm_status_t status;
 pid_state_t pid_state;
 int main(void)
+{
     // Initialize HAL
     hal_init();
     // Configure the system clock
     systemclock_init();
     // Unset bootloader option bytes (if set)
     // FIXME this was never getting called. Try again sometime.
     //bootloader_unset();
     // Init GPIO
     gpio_init();
     // Init USB (TODO: Handle plugged/unplugged with external power)
     MX_USB_DEVICE_Init();
 //    set.val.usb_plugged =
     // USB startup delay
     HAL_Delay(500);
     HAL_GPIO_WritePin(LED_POWER, 1);
     // Enter into bootloader if up button pressed on boot
     if(!HAL_GPIO_ReadPin(SW_UP))
         bootloader_enter();
     // Init SPI busses
     spi_init();
     // Init RTD chip
     #ifdef MAX31865_RTD_SENSOR
     max31865_config(spi_get());
     #endif
     // Init OLED over SPI
     ssd1306_init();
     ssd1306_clearscreen();
     // Startup screen
     display_startup_screen();
     // Default status
     status.temp = 0;
     status.temp_frac = 0;
     status.state_resume = 0;
     status.state = STATE_IDLE;
     status.setpoint = 70;
     status.pid_enabled = 0;
     pid_init(&pid_state);
     // Go to brew instead of idle if configured thusly
     if(set.val.boottobrew)
       status.state = STATE_PREHEAT;
     // Startup screen
     ssd1306_drawstring("therm v0.2", 1, 40);
     ssd1306_drawstring("protofusion.org/therm", 3, 0);
     HAL_Delay(1000);
     // Restore settings from flash memory
     flash_restore(&set);
-    HAL_Delay(1000);
+    HAL_Delay(2000);
     ssd1306_clearscreen();
     // Soft timers
     uint32_t last_ssr_on = 0;
     uint32_t last_vcp_tx = 0;
     uint32_t last_led = 0;
     uint32_t last_pid = 0;
     int16_t ssr_output = 0; // Duty cycle of ssr, 0 to SSR_PERIOD
     // Main loop
     while(1)
+    {
         // Process sensor inputs
         if(HAL_GetTick() - last_led > 400)
+        {
             last_led = HAL_GetTick();
+        }
         if((HAL_GetTick() - last_pid > PID_PERIOD))
+        {
             #ifdef MAX31855_TC_SENSOR
             max31855_readtemp(spi_get(), &set, &status); // Read MAX31855
             #endif
             #ifdef MAX31865_RTD_SENSOR
             max31865_readtemp(spi_get(), &set, &status);
 			#else
 			max31855_readtemp(spi_get(), &set, &status); // Read MAX31855
             #endif
             if(status.pid_enabled)
+            {
                 // Get ssr output for next time
-                int16_t power_percent = pid_update(set.val.k_p, set.val.k_i, set.val.k_d, status.temp, status.temp_frac, status.setpoint, &set, &status);
+                int16_t power_percent = pid_update(&set, &status, &pid_state);
                 //power-percent is 0-1000?
                 ssr_output = power_percent; //(((uint32_t)SSR_PERIOD * (uint32_t)10 * (uint32_t)100) * power_percent) / (uint32_t)1000000;
             	// put ssr output on display
                 ssd1306_drawstring("      ", 0, 90); //fixme: this is bad, but I can't get the old digits to clear otherwise
                 char tempstr[6];
                 itoa(ssr_output, tempstr, 10);
                 ssd1306_drawstring(tempstr, 0, 90);
+            }
             else
+            {
                 ssr_output = 0;
+            }
             last_pid = HAL_GetTick();
+        }
         // Kill SSR once the desired on-time has elapsed
         if(HAL_GetTick() - last_ssr_on > ssr_output || ssr_output <= 0)
+        {
             HAL_GPIO_WritePin(SSR_PIN, 0);
             HAL_GPIO_WritePin(LED_POWER, 0);
+        }
         // Every 200ms, set the SSR on unless output is 0
         if(HAL_GetTick() - last_ssr_on > SSR_PERIOD)
+        {
             // Only support heating (ssr_output > 0) right now
             if(ssr_output > 0)
+            {
                 char tempstr[6];
                 itoa(ssr_output, tempstr, 10);
                 ssd1306_drawstring(tempstr, 0, 90);
                 HAL_GPIO_WritePin(SSR_PIN, 1);
                 HAL_GPIO_WritePin(LED_POWER, 1);
                 last_ssr_on = HAL_GetTick();
+            }
             else {
                 // Make sure everything is off
                 HAL_GPIO_WritePin(SSR_PIN, 0);
                 HAL_GPIO_WritePin(LED_POWER, 0);
+            }
+        }
-        // Transmit temperature over USB-CDC on a regulat basis
+        // Transmit temperature over USB-CDC on a regular basis
         if(HAL_GetTick() - last_vcp_tx > VCP_TX_FREQ)
+        {
             // Print temp to cdc
             char tempstr[16];
             itoa_fp(status.temp, status.temp_frac, tempstr);
             uint8_t numlen = strlen(tempstr);
             tempstr[numlen] = '\r';
             tempstr[numlen+1] = '\n';
     //        if(set.val.usb_plugged)
     //            CDC_Transmit_FS(tempstr, numlen+2);
            // while(CDC_Transmit_FS("\r\n", 2) == USBD_BUSY);
             last_vcp_tx = HAL_GetTick();
+        }
         // Run state machine
         display_process(&set, &status);
+    }
+}
 // vim:softtabstop=4 shiftwidth=4 expandtab

max31865.c

➞

Show inline comments

 #include "max31855.h"
 // Registers
 #define MAX31865_REG_CONFIG 0x00
 #define MAX31865_REG_RTD_MSB 0x01
 #define MAX31865_REG_RTD_LSB 0x02
 #define MAX31865_REG_HFAULT_THRESH_MSB 0x03
 #define MAX31865_REG_HFAULT_THRESH_LSB 0x04
 #define MAX31865_REG_LFAULT_THRESH_MSB 0x05
 #define MAX31865_REG_LFAULT_THRESH_LSB 0x06
 #define MAX31865_REG_FAULTSTATUS 0x07
 #define MAX31865_REG_WRITE_MODIFIER 0x80
 // Fields
 #define MAX31865_CONF_VBIAS (1<<7)
 #define MAX31865_CONF_AUTO_CONVERT (1<<6)
 #define MAX31865_CONF_1SHOT (1<<5)
 #define MAX31865_CONF_3WIRE (1<<4)
 #define MAX31865_CONF_FAULT_NOACTION    0b0000
 #define MAX31865_CONF_FAULT_AUTODELAY   0b0100
 #define MAX31865_CONF_FAULT_MANUALELAY1 0b1000
 #define MAX31865_CONF_FAULT_MANUALELAY2 0b1100
 #define MAX31865_CONF_FAULT_CLEAR (1<<1)
 #define MAX31865_CONF_50_60HZ_FILTER (1<<0)
 void max31865_config(SPI_HandleTypeDef* hspi1)
+{
     uint8_t config = 0x00;
     config |= MAX31865_CONF_VBIAS;
     config |= MAX31865_CONF_AUTO_CONVERT;
     config |= MAX31865_CONF_FAULT_CLEAR;
     uint8_t reg = (MAX31865_REG_WRITE_MODIFIER | MAX31865_REG_CONFIG);
     // Assert CS
     HAL_GPIO_WritePin(MAX_CS, 0);
     HAL_SPI_Transmit(hspi1, &reg, 1, 100);
     HAL_SPI_Transmit(hspi1, &config, 1, 100);
     // Release CS
     HAL_GPIO_WritePin(MAX_CS, 1);
+}
 void max31865_clear_errors(SPI_HandleTypeDef* hspi1) {
 	max31865_config(hspi1);
+}
 // Grab temperature reading from MAX31865
 void max31865_readtemp(SPI_HandleTypeDef* hspi1, therm_settings_t* set, therm_status_t* status)
+{
     ///////////////////////////////////
     // This is duplicated from MAX31855, update for MAX31865 registers/etc
     ///////////////////////////////////
     // TODO: Set configuration register based on params in config.h (2-wire, 4-wire, etc RTD). This is register 0x00.
         // 2-wire RTC or 2-wire (duh) NTC thermistor will be the only options
         // Need option for resistance of RTD
         // These options should be stored in the set structure and should be menu-selectable
     // TODO: Set RTD ref resistance in set struct
     // Assert CS
     HAL_GPIO_WritePin(MAX_CS, 0);
     uint8_t regh = MAX31865_REG_RTD_MSB;
     uint8_t rxdatah[1] = {0x00};
     uint8_t rxdatal[1] = {0x00};
     HAL_SPI_Transmit(hspi1, &regh, 1, 100);
     HAL_SPI_Receive(hspi1, rxdatah, 1, 100);
     HAL_SPI_Receive(hspi1, rxdatal, 1, 100);
     // Release CS
     HAL_GPIO_WritePin(MAX_CS, 1);
     // Assemble data array into one var
     uint16_t adc_count = ((rxdatah[0] & 0x7F) << 8) | rxdatal[0];
     if((rxdatah[0] & 0x80) && !set->val.ignore_error) {
         // Assert CS
         HAL_GPIO_WritePin(MAX_CS, 0);
         uint8_t reg = MAX31865_REG_FAULTSTATUS;
         uint8_t data[1] = {0x00};
         HAL_SPI_Transmit(hspi1, &reg, 1, 100);
         HAL_SPI_Receive(hspi1, data, 1, 100);
         // Release CS
         HAL_GPIO_WritePin(MAX_CS, 1);
         status->error_code = data[0];
         HAL_Delay(400); // FIXME: remove?
         status->state_resume = status->state;
         status->state = STATE_TC_ERROR;
         status->temp = 0;
         status->temp_frac = 0;
+    }
     else
+    {
         // Convert to Fahrenheit
         if(set->val.temp_units == TEMP_UNITS_FAHRENHEIT)
+        {
         	//use all fixed point math!
         	//convert adc to resistance
         	//Rrtd = adc / range * Rref
         	status->temp = adc_count * 9830 * 10;
         	status->temp /= 32768;
         	//resistance to temp
         	//(x - in1) * (cal2 - cal1) / (in2 - in1) + cal1
         	status->temp = ((status->temp * 100) - 100000) * (39200 - 3200) / (175860 - 100000) + 3200;
         	//grab the fraction
         	status->temp_frac = (status->temp / 10) % 10;
         	//scale back to degrees
         	status->temp = status->temp / 100;
         	//add in the offset
             status->temp += set->val.temp_offset;
+        }
         // Convert to Celsius
         else
+        {
         	//use all fixed point math!
         	//convert adc to resistance
         	//Rrtd = adc / range * Rref
         	status->temp = adc_count * 9830 * 10;
         	status->temp /= 32768;
         	//resistance to temp
         	//(x - in1) * (cal2 - cal1) / (in2 - in1) + cal1
         	status->temp = ((status->temp * 10) - 10000) * (20000 - 0) / (17586 - 10000) + 0;
         	//grab the fraction
         	status->temp_frac = (status->temp / 10) % 10;
         	//scale back to degrees
         	status->temp = status->temp / 100;
         	//add in the offset
             status->temp += set->val.temp_offset;
+        }
+    }
+}
 // vim:softtabstop=4 shiftwidth=4 expandtab

pid.c

➞

Show inline comments

 #include "stm32f0xx_hal.h"
 #include "states.h"
 #include "pid.h"
 // PID implementation
 // TODO: Make struct that has the last_temp and i_state in it, pass by ref. Make struct that has other input values maybe.
 static int16_t last_pid_temp = 0;
 static uint8_t last_pid_temp_frac = 0;
 static int32_t i_state = 0;
 int16_t pid_update(uint16_t k_p, uint16_t k_i, uint16_t k_d, int16_t temp, uint8_t temp_frac, int16_t setpoint, therm_settings_t* set, therm_status_t* status)
 void pid_init(pid_state_t* state)
+{
 	state->i_state = 0;
 	state->last_pid_temp = 0;
 	state->last_pid_temp_frac = 0;
+}
 int16_t pid_update(therm_settings_t* set, therm_status_t* status, pid_state_t *state)
+{
   // Calculate instantaneous error
   int16_t error = setpoint - temp; // TODO: Use fixed point fraction
+  int16_t error = status->setpoint - status->temp; // TODO: Use fixed point fraction
   // Proportional component
   int32_t p_term = k_p * error;
+  int32_t p_term = set->val.k_p * error;
   // Error accumulator (integrator)
   i_state += error;
+  state->i_state += error;
   // to prevent the iTerm getting huge from lots of
   //  error, we use a "windup guard"
   // (this happens when the machine is first turned on and
   // it cant help be cold despite its best efforts)
   // not necessary, but this makes windup guard values
   // relative to the current iGain
-  int32_t windup_guard_res = set->val.windup_guard / k_i;
+  int32_t windup_guard_res = set->val.windup_guard / set->val.k_i;
   // Calculate integral term with windup guard
   if (i_state > windup_guard_res)
     i_state = windup_guard_res;
   else if (i_state < -windup_guard_res)
     i_state = -windup_guard_res;
   if (state->i_state > windup_guard_res)
 	  state->i_state = windup_guard_res;
   else if (state->i_state < -windup_guard_res)
 	  state->i_state = -windup_guard_res;
   int32_t i_term = k_i * i_state;
+  int32_t i_term = set->val.k_i * state->i_state;
   // Calculate differential term (slope since last iteration)
   int32_t d_term = (k_d * (status->temp - last_pid_temp));
+  int32_t d_term = (set->val.k_d * (status->temp - state->last_pid_temp));
   // Save temperature for next iteration
   last_pid_temp = status->temp;
   last_pid_temp_frac = status->temp_frac;
   state->last_pid_temp = status->temp;
   state->last_pid_temp_frac = status->temp_frac;
   int16_t result = p_term + i_term - d_term;
   // Put out tenths of percent, 0-1000.
   if(result > 1000)
     result = 1000;
   else if(result < -1000)
     result = -1000;
   // Return feedback
   return result;
+}

pid.h

➞

Show inline comments

 #ifndef PIDS_H
 #define PIDS_H
 #include "stm32f0xx_hal.h"
 #include "states.h"
 int16_t pid_update(uint16_t k_p, uint16_t k_i, uint16_t k_d, int16_t temp, uint8_t temp_frac, int16_t setpoint, therm_settings_t* set, therm_status_t* status);
 typedef struct {
 	int16_t last_pid_temp;
 	uint8_t last_pid_temp_frac;
 	int32_t i_state;
 } pid_state_t;
 void pid_init(pid_state_t* state);
 int16_t pid_update(therm_settings_t* set, therm_status_t* status, pid_state_t* state);
 #endif

0 comments (0 inline, 0 general)