therm Changeset - e28695e6887c · protofusion repositories

Changeset - e28695e6887c

Parent rev.

Child rev.

[Not reviewed]

cortex-f0

0 5 0

Ethan Zonca - 9 years ago 2015-06-01 17:09:22
ez@ethanzonca.com

Added temperature offset support

5 files changed with 52 insertions and 2 deletions:

display.c

gpio.c

gpio.h

main.c

states.h

0 comments (0 inline, 0 general)

display.c

➞

Show inline comments

@@ @@ -296,112 +296,142 @@ void display_process(therm_settings_t* s @@
             // Write text to OLED
             // [ therm :: set windup ]
             // [ g = 12         ]
             ssd1306_DrawString("Start on Boot", 0, 40);
             ssd1306_drawlogo();
             ssd1306_DrawString("sob=", 1, 45);
             if(set->boottobrew)
                 ssd1306_DrawString("Enabled ", 1, 70);
             else
                 ssd1306_DrawString("Disabled", 1, 70);
             ssd1306_DrawString("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETUNITS;
+            }
             else if(!HAL_GPIO_ReadPin(SW_UP)) {
                 set->boottobrew = 1;
+            }
             else if(!HAL_GPIO_ReadPin(SW_DOWN)) {
                 set->boottobrew = 0;
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETUNITS:
+        {
             // Write text to OLED
             // [ therm :: set windup ]
             // [ g = 12         ]
             ssd1306_DrawString("Units: ", 0, 40);
             ssd1306_drawlogo();
             if(set->temp_units == TEMP_UNITS_FAHRENHEIT)
                 ssd1306_DrawString("Fahrenheit", 1, 60);
             else
                 ssd1306_DrawString("Celsius   ", 1, 60);
             ssd1306_DrawString("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 save_settings();
                 status->state = STATE_IDLE;
                 status->state = STATE_SETTEMPOFFSET;
+            }
             else if(!HAL_GPIO_ReadPin(SW_UP)) {
                 set->temp_units = TEMP_UNITS_FAHRENHEIT;
+            }
             else if(!HAL_GPIO_ReadPin(SW_DOWN)) {
                 set->temp_units = TEMP_UNITS_CELSIUS;
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETTEMPOFFSET:
+        {
             // Write text to OLED
             // [ therm :: set temp offset ]
             // [ g = 12         ]
             ssd1306_DrawString("Thermocouple Offset", 0, 40);
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->temp_offset, tempstr, 10);
             ssd1306_DrawString("O=", 1, 45);
             ssd1306_DrawString("    ", 1, 57);
             ssd1306_DrawString(tempstr, 1, 57);
             ssd1306_DrawString("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 save_settings();
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input_signed(&set->temp_offset);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_PREHEAT_BREW:
+        {
             // Write text to OLED
             // [ therm : preheating brew ]
             // [ 30 => 120 C             ]
             ssd1306_DrawString("Preheating...", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->setpoint_brew;
             // Button handler
             if(SW_BTN_PRESSED) {
 		save_setpoints(); // TODO: Check for mod
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input(&set->setpoint_brew);
+            }
             // Event Handler
             if(status->temp >= status->setpoint) {
                 status->state = STATE_MAINTAIN_BREW;
+            }
         } break;
         case STATE_MAINTAIN_BREW:
+        {
             // Write text to OLED
             // [ therm : ready to brew ]
             // [ 30 => 120 C           ]
             ssd1306_DrawString("Preheated!", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->setpoint_brew;
             // Button handler
             if(SW_BTN_PRESSED) {
 		save_setpoints(); // TODO: Check for mod
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input(&set->setpoint_brew);
+            }

gpio.c

➞

Show inline comments

 #include "gpio.h"
 #include "config.h"
 #include "stm32f0xx_hal_conf.h"
 #include <inttypes.h>
 // Increase on each press, and increase at a fast rate after duration elapsed of continuously holding down... somehow...
 uint32_t change_time_reset = 0;
 void user_input(uint16_t* to_modify)
+{
     if(CHANGE_ELAPSED) {
         if(!HAL_GPIO_ReadPin(SW_UP) ) {
             CHANGE_RESET;
             (*to_modify)++;
+        }
         else if(!HAL_GPIO_ReadPin(SW_DOWN) && (*to_modify) > 0) {
             CHANGE_RESET;
             (*to_modify)--;
+        }
+    }
+}
 void user_input_signed(int16_t* to_modify)
+{
     // TODO: Bounds check on int16_t
     if(CHANGE_ELAPSED) {
         if(!HAL_GPIO_ReadPin(SW_UP) ) {
             CHANGE_RESET;
             (*to_modify)++;
+        }
         else if(!HAL_GPIO_ReadPin(SW_DOWN)) {
             CHANGE_RESET;
             (*to_modify)--;
+        }
+    }
+}
 void init_gpio(void) {
   GPIO_InitTypeDef GPIO_InitStruct;
     /* GPIO Ports Clock Enable */
   __GPIOF_CLK_ENABLE();
   __GPIOA_CLK_ENABLE();
   __GPIOB_CLK_ENABLE();
   __SPI1_CLK_ENABLE();
   //////////////////
   // PORT F       //
   //////////////////
   // PORTF OUTPUT
   // Configure GPIO pin : PF0 [Power LED]
   GPIO_InitStruct.Pin = GPIO_PIN_0;
   GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
   HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
   // PORTF UNUSED
   // Configure GPIO pin : PF1
   GPIO_InitStruct.Pin = GPIO_PIN_1;
   GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);
   //////////////////
   // PORT A       //
   //////////////////
   // PORT A OUTPUT
   // Configure GPIO pins : (SSR+ CS_OLED RES D/C CS_MAX)
   GPIO_InitStruct.Pin = GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_3|GPIO_PIN_4|GPIO_PIN_15;
   GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   GPIO_InitStruct.Speed = GPIO_SPEED_LOW;
   HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
   // PORTA INPUT
   // Configure GPIO pin : PA15
 //  GPIO_InitStruct.Pin = GPIO_PIN_15;
 //  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;

gpio.h

➞

Show inline comments

 #ifndef GPIO_H
 #define GPIO_H
 #include <inttypes.h>
 #define CHANGE_PERIOD_MS 100
 #define CHANGE_ELAPSED (HAL_GetTick() - change_time_reset) > CHANGE_PERIOD_MS
 #define CHANGE_RESET change_time_reset = HAL_GetTick()
 void user_input(uint16_t* to_modify);
 void user_input_signed(int16_t* to_modify);
 void init_gpio(void);
 #endif
 // vim:softtabstop=4 shiftwidth=4 expandtab

main.c

➞

Show inline comments

@@ @@ -161,102 +161,104 @@ void update_temp() { @@
     uint16_t temp_pre = rxdatal[0] | (rxdatah[0]<<8);
     if(temp_pre & 0b0000000000000010) {
         ssd1306_clearscreen();
         //ssd1306_DrawString("Fatal Error", 3, 35);
         HAL_Delay(100);
         status.state = STATE_TC_ERROR;
         status.temp = 0;
         status.temp_frac = 0;
+    }
     else if(temp_pre & 0b0000000000000001 && !set.ignore_tc_error) {
         status.state_resume = status.state;
         status.state = STATE_TC_ERROR;
         status.temp = 0;
         status.temp_frac = 0;
+    }
     else
+    {
         if(status.state == STATE_TC_ERROR)
+        {
             status.state = status.state_resume;
             ssd1306_clearscreen();
+        }
         uint8_t sign = status.temp >> 15;// top bit is sign
         temp_pre = temp_pre >> 2; // Drop 2 lowest bits
         status.temp_frac = temp_pre & 0b11; // get fractional part
         status.temp_frac *= 25; // each bit is .25 a degree, up to fixed point
         temp_pre = temp_pre >> 2; // Drop 2 fractional bits
         int8_t signint;
         if(sign) {
             signint = -1;
+        }
         else {
             signint = 1;
+        }
         // Convert to Fahrenheit
         if(set.temp_units == TEMP_UNITS_FAHRENHEIT)
+        {
             status.temp = signint * ((temp_pre*100) + status.temp_frac);
             status.temp = status.temp * 1.8;
             status.temp += 3200;
             status.temp_frac = status.temp % 100;
             status.temp /= 100;
             status.temp += set.temp_offset;
+        }
         // Use Celsius values
         else
+        {
             status.temp = temp_pre * signint;
             status.temp += set.temp_offset;
+        }
+    }
+}
 // PID implementation
 // TODO: Make struct that has the last_temp and i_state in it, pass by ref. Make struct that has other input values maybe.
 int16_t last_pid_temp = 0;
 uint8_t last_pid_temp_frac = 0;
 int16_t i_state = 0;
 int16_t update_pid(uint16_t k_p, uint16_t k_i, uint16_t k_d, int16_t temp, uint8_t temp_frac, int16_t setpoint)
+{
   // Calculate instantaneous error
   int16_t error = (int16_t)setpoint - (int16_t)temp; // TODO: Use fixed point fraction
   // Proportional component
   int16_t p_term = k_p * error;
   // Error accumulator (integrator)
   i_state += error;
   // to prevent the iTerm getting huge despite lots of
   //  error, we use a "windup guard"
   // (this happens when the machine is first turned on and
   // it cant help be cold despite its best efforts)
   // not necessary, but this makes windup guard values
   // relative to the current iGain
   int16_t windup_guard_res = set.windup_guard / k_i;
   // Calculate integral term with windup guard
   if (i_state > windup_guard_res)
     i_state = windup_guard_res;
   else if (i_state < -windup_guard_res)
     i_state = -windup_guard_res;
   int16_t i_term = k_i * i_state;
   // Calculate differential term (slope since last iteration)
   int16_t d_term = (k_d * (status.temp - last_pid_temp));
   // Save temperature for next iteration
   last_pid_temp = status.temp;
   last_pid_temp_frac = status.temp_frac;
   int16_t result = p_term + i_term - d_term;
   // Put out tenths of percent, 0-1000.
   if(result > 1000)

states.h

➞

Show inline comments

 #ifndef STATES_H
 #define STATES_H
 typedef struct {
     int32_t temp;
     uint8_t temp_frac;
     uint8_t state_resume;
     uint8_t state;
     int32_t setpoint;
     uint8_t pid_enabled;
 } therm_status_t;
 typedef struct {
     uint8_t boottobrew;
     uint8_t temp_units;
     uint16_t windup_guard;
     uint16_t k_p;
     uint16_t k_i;
     uint16_t k_d;
     int16_t temp_offset;
     uint8_t ignore_tc_error;
     int16_t setpoint_brew;
     int16_t setpoint_steam;
 } therm_settings_t;
 enum tempunits {
     TEMP_UNITS_CELSIUS = 0,
     TEMP_UNITS_FAHRENHEIT,
 };
 enum state {
     STATE_IDLE = 0,
     STATE_SETP,
     STATE_SETI,
     STATE_SETD,
     STATE_SETSTEPS,
     STATE_SETWINDUP,
     STATE_SETBOOTTOBREW,
     STATE_SETUNITS,
     STATE_SETTEMPOFFSET,
     STATE_PREHEAT_BREW,
     STATE_MAINTAIN_BREW,
     STATE_PREHEAT_STEAM,
     STATE_MAINTAIN_STEAM,
     STATE_TC_ERROR
 };
 #endif

0 comments (0 inline, 0 general)