diff --git a/system_stm32f0xx.c b/system_stm32f0xx.c deleted file mode 100644 --- a/system_stm32f0xx.c +++ /dev/null @@ -1,385 +0,0 @@ -/** - ****************************************************************************** - * @file system_stm32f0xx.c - * @author MCD Application Team - * @version V1.0.0 - * @date 23-March-2012 - * @brief CMSIS Cortex-M0 Device Peripheral Access Layer System Source File. - * This file contains the system clock configuration for STM32F0xx devices, - * and is customized for use with STM32F0-DISCOVERY Kit. - * The STM32F0xx is configured to run at 48 MHz, following the three - * configuration below: - * - PLL_SOURCE_HSI (default): HSI (~8MHz) used to clock the PLL, and - * the PLL is used as system clock source. - * - PLL_SOURCE_HSE : HSE (8MHz) used to clock the PLL, and - * the PLL is used as system clock source. - * - PLL_SOURCE_HSE_BYPASS : HSE bypassed with an external clock - * (8MHz, coming from ST-Link) used to clock - * the PLL, and the PLL is used as system - * clock source. - * - * - * 1. This file provides two functions and one global variable to be called from - * user application: - * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier - * and Divider factors, AHB/APBx prescalers and Flash settings), - * depending on the configuration selected (see above). - * This function is called at startup just after reset and - * before branch to main program. This call is made inside - * the "startup_stm32f0xx.s" file. - * - * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used - * by the user application to setup the SysTick - * timer or configure other parameters. - * - * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must - * be called whenever the core clock is changed - * during program execution. - * - * 2. After each device reset the HSI (8 MHz Range) is used as system clock source. - * Then SystemInit() function is called, in "startup_stm32f0xx.s" file, to - * configure the system clock before to branch to main program. - * - * 3. If the system clock source selected by user fails to startup, the SystemInit() - * function will do nothing and HSI still used as system clock source. User can - * add some code to deal with this issue inside the SetSysClock() function. - * - * 4. The default value of HSE crystal is set to 8MHz, refer to "HSE_VALUE" define - * in "stm32f0xx.h" file. When HSE is used as system clock source, directly or - * through PLL, and you are using different crystal you have to adapt the HSE - * value to your own configuration. - * - ****************************************************************************** - * @attention - * - *

© COPYRIGHT 2012 STMicroelectronics

- * - * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); - * You may not use this file except in compliance with the License. - * You may obtain a copy of the License at: - * - * http://www.st.com/software_license_agreement_liberty_v2 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, - * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - * See the License for the specific language governing permissions and - * limitations under the License. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32f0xx_system - * @{ - */ - -/** @addtogroup STM32F0xx_System_Private_Includes - * @{ - */ - -#include "stm32f0xx.h" - -/** - * @} - */ - -/** @addtogroup STM32F0xx_System_Private_TypesDefinitions - * @{ - */ - -/** - * @} - */ - -/** @addtogroup STM32F0xx_System_Private_Defines - * @{ - */ -/* Select the PLL clock source */ - -#define PLL_SOURCE_HSI // HSI (~8MHz) used to clock the PLL, and the PLL is used as system clock source -//#define PLL_SOURCE_HSE // HSE (8MHz) used to clock the PLL, and the PLL is used as system clock source -//#define PLL_SOURCE_HSE_BYPASS // HSE bypassed with an external clock (8MHz, coming from ST-Link) used to clock - // the PLL, and the PLL is used as system clock source - -/** - * @} - */ - -/** @addtogroup STM32F0xx_System_Private_Macros - * @{ - */ - -/** - * @} - */ - -/** @addtogroup STM32F0xx_System_Private_Variables - * @{ - */ -uint32_t SystemCoreClock = 48000000; -__I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; - -/** - * @} - */ - -/** @addtogroup STM32F0xx_System_Private_FunctionPrototypes - * @{ - */ - -static void SetSysClock(void); - -/** - * @} - */ - -/** @addtogroup STM32F0xx_System_Private_Functions - * @{ - */ - -/** - * @brief Setup the microcontroller system. - * Initialize the Embedded Flash Interface, the PLL and update the - * SystemCoreClock variable. - * @param None - * @retval None - */ -void SystemInit (void) -{ - /* Set HSION bit */ - RCC->CR |= (uint32_t)0x00000001; - - /* Reset SW[1:0], HPRE[3:0], PPRE[2:0], ADCPRE and MCOSEL[2:0] bits */ - RCC->CFGR &= (uint32_t)0xF8FFB80C; - - /* Reset HSEON, CSSON and PLLON bits */ - RCC->CR &= (uint32_t)0xFEF6FFFF; - - /* Reset HSEBYP bit */ - RCC->CR &= (uint32_t)0xFFFBFFFF; - - /* Reset PLLSRC, PLLXTPRE and PLLMUL[3:0] bits */ - RCC->CFGR &= (uint32_t)0xFFC0FFFF; - - /* Reset PREDIV1[3:0] bits */ - RCC->CFGR2 &= (uint32_t)0xFFFFFFF0; - - /* Reset USARTSW[1:0], I2CSW, CECSW and ADCSW bits */ - RCC->CFGR3 &= (uint32_t)0xFFFFFEAC; - - /* Reset HSI14 bit */ - RCC->CR2 &= (uint32_t)0xFFFFFFFE; - - /* Disable all interrupts */ - RCC->CIR = 0x00000000; - - /* Configure the System clock frequency, AHB/APBx prescalers and Flash settings */ - SetSysClock(); -} - -/** - * @brief Update SystemCoreClock according to Clock Register Values - * The SystemCoreClock variable contains the core clock (HCLK), it can - * be used by the user application to setup the SysTick timer or configure - * other parameters. - * - * @note Each time the core clock (HCLK) changes, this function must be called - * to update SystemCoreClock variable value. Otherwise, any configuration - * based on this variable will be incorrect. - * - * @note - The system frequency computed by this function is not the real - * frequency in the chip. It is calculated based on the predefined - * constant and the selected clock source: - * - * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) - * - * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) - * - * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) - * or HSI_VALUE(*) multiplied/divided by the PLL factors. - * - * (*) HSI_VALUE is a constant defined in stm32f0xx.h file (default value - * 8 MHz) but the real value may vary depending on the variations - * in voltage and temperature. - * - * (**) HSE_VALUE is a constant defined in stm32f0xx.h file (default value - * 8 MHz), user has to ensure that HSE_VALUE is same as the real - * frequency of the crystal used. Otherwise, this function may - * have wrong result. - * - * - The result of this function could be not correct when using fractional - * value for HSE crystal. - * @param None - * @retval None - */ -void SystemCoreClockUpdate (void) -{ - uint32_t tmp = 0, pllmull = 0, pllsource = 0, prediv1factor = 0; - - /* Get SYSCLK source -------------------------------------------------------*/ - tmp = RCC->CFGR & RCC_CFGR_SWS; - - switch (tmp) - { - case 0x00: /* HSI used as system clock */ - SystemCoreClock = HSI_VALUE; - break; - case 0x04: /* HSE used as system clock */ - SystemCoreClock = HSE_VALUE; - break; - case 0x08: /* PLL used as system clock */ - /* Get PLL clock source and multiplication factor ----------------------*/ - pllmull = RCC->CFGR & RCC_CFGR_PLLMULL; - pllsource = RCC->CFGR & RCC_CFGR_PLLSRC; - pllmull = ( pllmull >> 18) + 2; - - if (pllsource == 0x00) - { - /* HSI oscillator clock divided by 2 selected as PLL clock entry */ - SystemCoreClock = (HSI_VALUE >> 1) * pllmull; - } - else - { - prediv1factor = (RCC->CFGR2 & RCC_CFGR2_PREDIV1) + 1; - /* HSE oscillator clock selected as PREDIV1 clock entry */ - SystemCoreClock = (HSE_VALUE / prediv1factor) * pllmull; - } - break; - default: /* HSI used as system clock */ - SystemCoreClock = HSI_VALUE; - break; - } - /* Compute HCLK clock frequency ----------------*/ - /* Get HCLK prescaler */ - tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)]; - /* HCLK clock frequency */ - SystemCoreClock >>= tmp; -} - -/** - * @brief Configures the System clock frequency, AHB/APBx prescalers and Flash - * settings. - * @note This function should be called only once the RCC clock configuration - * is reset to the default reset state (done in SystemInit() function). - * @param None - * @retval None - */ -static void SetSysClock(void) -{ - __IO uint32_t StartUpCounter = 0, HSEStatus = 0; - - /* SYSCLK, HCLK, PCLK configuration ----------------------------------------*/ -#if defined (PLL_SOURCE_HSI) - /* At this stage the HSI is already enabled */ - - /* Enable Prefetch Buffer and set Flash Latency */ - FLASH->ACR = FLASH_ACR_PRFTBE | FLASH_ACR_LATENCY; - - /* HCLK = SYSCLK */ - RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; - - /* PCLK = HCLK */ - RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE_DIV1; - - /* PLL configuration = (HSI/2) * 12 = ~48 MHz */ - RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); - RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSI_Div2 | RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLMULL12); - - /* Enable PLL */ - RCC->CR |= RCC_CR_PLLON; - - /* Wait till PLL is ready */ - while((RCC->CR & RCC_CR_PLLRDY) == 0) - { - } - - /* Select PLL as system clock source */ - RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); - RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; - - /* Wait till PLL is used as system clock source */ - while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)RCC_CFGR_SWS_PLL) - { - } -#else - #if defined (PLL_SOURCE_HSE) - /* Enable HSE */ - RCC->CR |= ((uint32_t)RCC_CR_HSEON); - #elif defined (PLL_SOURCE_HSE_BYPASS) - /* HSE oscillator bypassed with external clock */ - RCC->CR |= (uint32_t)(RCC_CR_HSEON | RCC_CR_HSEBYP); - #endif /* PLL_SOURCE_HSE */ - - /* Wait till HSE is ready and if Time out is reached exit */ - do - { - HSEStatus = RCC->CR & RCC_CR_HSERDY; - StartUpCounter++; - } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); - - if ((RCC->CR & RCC_CR_HSERDY) != RESET) - { - HSEStatus = (uint32_t)0x01; - } - else - { - HSEStatus = (uint32_t)0x00; - } - - if (HSEStatus == (uint32_t)0x01) - { - /* Enable Prefetch Buffer and set Flash Latency */ - FLASH->ACR = FLASH_ACR_PRFTBE | FLASH_ACR_LATENCY; - - /* HCLK = SYSCLK */ - RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; - - /* PCLK = HCLK */ - RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE_DIV1; - - /* PLL configuration = HSE * 6 = 48 MHz */ - RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLXTPRE | RCC_CFGR_PLLMULL)); - RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_PREDIV1 | RCC_CFGR_PLLXTPRE_PREDIV1 | RCC_CFGR_PLLMULL6); - - /* Enable PLL */ - RCC->CR |= RCC_CR_PLLON; - - /* Wait till PLL is ready */ - while((RCC->CR & RCC_CR_PLLRDY) == 0) - { - } - - /* Select PLL as system clock source */ - RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); - RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; - - /* Wait till PLL is used as system clock source */ - while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)RCC_CFGR_SWS_PLL) - { - } - } - else - { /* If HSE fails to start-up, the application will have wrong clock - configuration. User can add here some code to deal with this error */ - } -#endif /* PLL_SOURCE_HSI */ -} - -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ -