diff --git a/system_stm32l1xx.c b/system_stm32l1xx.c deleted file mode 100644 --- a/system_stm32l1xx.c +++ /dev/null @@ -1,399 +0,0 @@ -/** - ****************************************************************************** - * @file system_stm32l1xx.c - * @author MCD Application Team - * @version V1.2.0 - * @date 11-July-2014 - * @brief CMSIS Cortex-M3 Device Peripheral Access Layer System Source File. - * This file contains the system clock configuration for STM32L1xx Ultra - * Low power devices, and is generated by the clock configuration - * tool STM32L1xx_Clock_Configuration_V1.2.0.xls - * - * 1. This file provides two functions and one global variable to be called from - * user application: - * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier - * and Divider factors, AHB/APBx prescalers and Flash settings), - * depending on the configuration made in the clock xls tool. - * This function is called at startup just after reset and - * before branch to main program. This call is made inside - * the "startup_stm32l1xx_xx.s" file. - * - * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used - * by the user application to setup the SysTick - * timer or configure other parameters. - * - * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must - * be called whenever the core clock is changed - * during program execution. - * - * 2. After each device reset the MSI (2.1 MHz Range) is used as system clock source. - * Then SystemInit() function is called, in "startup_stm32l1xx_xx.s" file, to - * configure the system clock before to branch to main program. - * - * 3. If the system clock source selected by user fails to startup, the SystemInit() - * function will do nothing and MSI still used as system clock source. User can - * add some code to deal with this issue inside the SetSysClock() function. - * - * 4. The default value of HSE crystal is set to 8MHz, refer to "HSE_VALUE" define - * in "stm32l1xx.h" file. When HSE is used as system clock source, directly or - * through PLL, and you are using different crystal you have to adapt the HSE - * value to your own configuration. - * - * 5. This file configures the system clock as follows: - *============================================================================= - * System Clock Configuration - *============================================================================= - * System Clock source | PLL(HSE) - *----------------------------------------------------------------------------- - * SYSCLK | 32000000 Hz - *----------------------------------------------------------------------------- - * HCLK | 32000000 Hz - *----------------------------------------------------------------------------- - * AHB Prescaler | 1 - *----------------------------------------------------------------------------- - * APB1 Prescaler | 1 - *----------------------------------------------------------------------------- - * APB2 Prescaler | 1 - *----------------------------------------------------------------------------- - * HSE Frequency | 4000000 Hz - *----------------------------------------------------------------------------- - * PLL DIV | 3 - *----------------------------------------------------------------------------- - * PLL MUL | 24 - *----------------------------------------------------------------------------- - * VDD | 3.3 V - *----------------------------------------------------------------------------- - * Vcore | 1.8 V (Range 1) - *----------------------------------------------------------------------------- - * Flash Latency | 1 WS - *----------------------------------------------------------------------------- - * Require 48MHz for USB clock | Enabled - *----------------------------------------------------------------------------- - *============================================================================= - * @attention - * - *

© COPYRIGHT 2013 STMicroelectronics

- * - * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); - * You may not use this file except in compliance with the License. - * You may obtain a copy of the License at: - * - * http://www.st.com/software_license_agreement_liberty_v2 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, - * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - * See the License for the specific language governing permissions and - * limitations under the License. - * - ****************************************************************************** - */ - -/** @addtogroup CMSIS - * @{ - */ - -/** @addtogroup stm32l1xx_system - * @{ - */ - -/** @addtogroup STM32L1xx_System_Private_Includes - * @{ - */ - -#include "stm32l1xx.h" - -/** - * @} - */ - -/** @addtogroup STM32L1xx_System_Private_TypesDefinitions - * @{ - */ - -/** - * @} - */ - -/** @addtogroup STM32L1xx_System_Private_Defines - * @{ - */ - -/*!< Uncomment the following line if you need to relocate your vector Table in - Internal SRAM. */ -/* #define VECT_TAB_SRAM */ -#define VECT_TAB_OFFSET 0x0 /*!< Vector Table base offset field. - This value must be a multiple of 0x200. */ -/** - * @} - */ - -/** @addtogroup STM32L1xx_System_Private_Macros - * @{ - */ - -/** - * @} - */ - -/** @addtogroup STM32L1xx_System_Private_Variables - * @{ - */ -uint32_t SystemCoreClock = 32000000; -__I uint8_t PLLMulTable[9] = {3, 4, 6, 8, 12, 16, 24, 32, 48}; -__I uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; - -/** - * @} - */ - -/** @addtogroup STM32L1xx_System_Private_FunctionPrototypes - * @{ - */ - -static void SetSysClock(void); - -/** - * @} - */ - -/** @addtogroup STM32L1xx_System_Private_Functions - * @{ - */ - -/** - * @brief Setup the microcontroller system. - * Initialize the Embedded Flash Interface, the PLL and update the - * SystemCoreClock variable. - * @param None - * @retval None - */ -void SystemInit (void) -{ - /*!< Set MSION bit */ - RCC->CR |= (uint32_t)0x00000100; - - /*!< Reset SW[1:0], HPRE[3:0], PPRE1[2:0], PPRE2[2:0], MCOSEL[2:0] and MCOPRE[2:0] bits */ - RCC->CFGR &= (uint32_t)0x88FFC00C; - - /*!< Reset HSION, HSEON, CSSON and PLLON bits */ - RCC->CR &= (uint32_t)0xEEFEFFFE; - - /*!< Reset HSEBYP bit */ - RCC->CR &= (uint32_t)0xFFFBFFFF; - - /*!< Reset PLLSRC, PLLMUL[3:0] and PLLDIV[1:0] bits */ - RCC->CFGR &= (uint32_t)0xFF02FFFF; - - /*!< Disable all interrupts */ - RCC->CIR = 0x00000000; - - /* Configure the System clock frequency, AHB/APBx prescalers and Flash settings */ - SetSysClock(); - -#ifdef VECT_TAB_SRAM - SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */ -#else - SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH. */ -#endif -} - -/** - * @brief Update SystemCoreClock according to Clock Register Values - * The SystemCoreClock variable contains the core clock (HCLK), it can - * be used by the user application to setup the SysTick timer or configure - * other parameters. - * - * @note Each time the core clock (HCLK) changes, this function must be called - * to update SystemCoreClock variable value. Otherwise, any configuration - * based on this variable will be incorrect. - * - * @note - The system frequency computed by this function is not the real - * frequency in the chip. It is calculated based on the predefined - * constant and the selected clock source: - * - * - If SYSCLK source is MSI, SystemCoreClock will contain the MSI - * value as defined by the MSI range. - * - * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) - * - * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) - * - * - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) - * or HSI_VALUE(*) multiplied/divided by the PLL factors. - * - * (*) HSI_VALUE is a constant defined in stm32l1xx.h file (default value - * 16 MHz) but the real value may vary depending on the variations - * in voltage and temperature. - * - * (**) HSE_VALUE is a constant defined in stm32l1xx.h file (default value - * 8 MHz), user has to ensure that HSE_VALUE is same as the real - * frequency of the crystal used. Otherwise, this function may - * have wrong result. - * - * - The result of this function could be not correct when using fractional - * value for HSE crystal. - * @param None - * @retval None - */ -void SystemCoreClockUpdate (void) -{ - uint32_t tmp = 0, pllmul = 0, plldiv = 0, pllsource = 0, msirange = 0; - - /* Get SYSCLK source -------------------------------------------------------*/ - tmp = RCC->CFGR & RCC_CFGR_SWS; - - switch (tmp) - { - case 0x00: /* MSI used as system clock */ - msirange = (RCC->ICSCR & RCC_ICSCR_MSIRANGE) >> 13; - SystemCoreClock = (32768 * (1 << (msirange + 1))); - break; - case 0x04: /* HSI used as system clock */ - SystemCoreClock = HSI_VALUE; - break; - case 0x08: /* HSE used as system clock */ - SystemCoreClock = HSE_VALUE; - break; - case 0x0C: /* PLL used as system clock */ - /* Get PLL clock source and multiplication factor ----------------------*/ - pllmul = RCC->CFGR & RCC_CFGR_PLLMUL; - plldiv = RCC->CFGR & RCC_CFGR_PLLDIV; - pllmul = PLLMulTable[(pllmul >> 18)]; - plldiv = (plldiv >> 22) + 1; - - pllsource = RCC->CFGR & RCC_CFGR_PLLSRC; - - if (pllsource == 0x00) - { - /* HSI oscillator clock selected as PLL clock entry */ - SystemCoreClock = (((HSI_VALUE) * pllmul) / plldiv); - } - else - { - /* HSE selected as PLL clock entry */ - SystemCoreClock = (((HSE_VALUE) * pllmul) / plldiv); - } - break; - default: /* MSI used as system clock */ - msirange = (RCC->ICSCR & RCC_ICSCR_MSIRANGE) >> 13; - SystemCoreClock = (32768 * (1 << (msirange + 1))); - break; - } - /* Compute HCLK clock frequency --------------------------------------------*/ - /* Get HCLK prescaler */ - tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)]; - /* HCLK clock frequency */ - SystemCoreClock >>= tmp; -} - -/** - * @brief Configures the System clock frequency, AHB/APBx prescalers and Flash - * settings. - * @note This function should be called only once the RCC clock configuration - * is reset to the default reset state (done in SystemInit() function). - * @param None - * @retval None - */ -uint8_t clock_fail = 0; - -static void SetSysClock(void) -{ - __IO uint32_t StartUpCounter = 0, HSEStatus = 0; - - /* SYSCLK, HCLK, PCLK2 and PCLK1 configuration ---------------------------*/ - /* Enable HSE */ - RCC->CR |= ((uint32_t)RCC_CR_HSEON); - - /* Wait till HSE is ready and if Time out is reached exit */ - do - { - HSEStatus = RCC->CR & RCC_CR_HSERDY; - StartUpCounter++; - } while((HSEStatus == 0) && (StartUpCounter != HSE_STARTUP_TIMEOUT)); - - if ((RCC->CR & RCC_CR_HSERDY) != RESET) - { - HSEStatus = (uint32_t)0x01; - } - else - { - HSEStatus = (uint32_t)0x00; - } - - if (HSEStatus == (uint32_t)0x01) - { - /* Enable 64-bit access */ - FLASH->ACR |= FLASH_ACR_ACC64; - - /* Enable Prefetch Buffer */ - FLASH->ACR |= FLASH_ACR_PRFTEN; - - /* Flash 1 wait state */ - FLASH->ACR |= FLASH_ACR_LATENCY; - - /* Power enable */ - RCC->APB1ENR |= RCC_APB1ENR_PWREN; - - /* Select the Voltage Range 1 (1.8 V) */ - PWR->CR = PWR_CR_VOS_0; - - /* Wait Until the Voltage Regulator is ready */ - while((PWR->CSR & PWR_CSR_VOSF) != RESET) - { - } - - /* HCLK = SYSCLK /1*/ - RCC->CFGR |= (uint32_t)RCC_CFGR_HPRE_DIV1; - - /* PCLK2 = HCLK /1*/ - RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE2_DIV1; - - /* PCLK1 = HCLK /1*/ - RCC->CFGR |= (uint32_t)RCC_CFGR_PPRE1_DIV1; - - /* PLL configuration */ - RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_PLLSRC | RCC_CFGR_PLLMUL | - RCC_CFGR_PLLDIV)); - RCC->CFGR |= (uint32_t)(RCC_CFGR_PLLSRC_HSE | RCC_CFGR_PLLMUL24 | RCC_CFGR_PLLDIV3); - - /* Enable PLL */ - RCC->CR |= RCC_CR_PLLON; - - /* Wait till PLL is ready */ - while((RCC->CR & RCC_CR_PLLRDY) == 0) - { - } - - /* Select PLL as system clock source */ - RCC->CFGR &= (uint32_t)((uint32_t)~(RCC_CFGR_SW)); - RCC->CFGR |= (uint32_t)RCC_CFGR_SW_PLL; - - /* Wait till PLL is used as system clock source */ - while ((RCC->CFGR & (uint32_t)RCC_CFGR_SWS) != (uint32_t)RCC_CFGR_SWS_PLL) - { - } - } - else - { - clock_fail = 1; -// while(1); - /* If HSE fails to start-up, the application will have wrong clock - configuration. User can add here some code to deal with this error */ - } -} - -/** - * @} - */ - -/** - * @} - */ - -/** - * @} - */ - -/******************* (C) COPYRIGHT 2013 STMicroelectronics *****END OF FILE****/ -