therm Changeset - 6d43230d5986 · protofusion repositories

Changeset - 6d43230d5986

Parent rev.

Child rev.

[Not reviewed]

tip rtd

0 3 0

matthewreed - 6 years ago 2018-11-25 21:08:06

Untested changes for RTDs

3 files changed with 30 insertions and 14 deletions:

display.c

max31865.c

pid.c

0 comments (0 inline, 0 general)

display.c

➞

Show inline comments

@@ @@ -25,7 +25,7 @@ static uint8_t sw_right_last = 0; @@
 static uint8_t trigger_drawsetpoint = 1;
 static int16_t last_temp = 21245;
 static int16_t last_temp_frac = 21245;
-static int16_t last_state = STATE_IDLE;
+static int16_t last_state = STATE_RESET;
 static uint8_t goto_mode = MODE_HEAT;
 static uint8_t reset_mode = RESET_REBOOT;
@@ @@ -409,8 +409,20 @@ void display_process(therm_settings_t* s @@
             itoa(status->error_code, tempstr, 10);
             ssd1306_drawstring(tempstr, 0, 57);
             //TODO: add RTD error codes
 			#ifdef MAX31865_RTD_SENSOR
             // RTD error codes
             if(status->error_code & 0b00000100)
                 ssd1306_drawstring(" RTD Over/Undervolt", 1, 0);
             else if(status->error_code & 0b00001000)
                 ssd1306_drawstring("    RTD FORCE- Open", 1, 0);
             else if(status->error_code & 0b00010000)
                 ssd1306_drawstring("RTD REF FORCE- Open", 1, 0);
             else if(status->error_code & 0b00100000)
                 ssd1306_drawstring("    RTD REFIN- High", 1, 0);
             else
                 ssd1306_drawstring("#?, Unknown Error", 1, 0);
 			#else
             // TC error codes
             if(status->error_code == 1)
                 ssd1306_drawstring("    TC Open Circuit", 1, 0);
             else if(status->error_code == 4)
@@ @@ -419,6 +431,7 @@ void display_process(therm_settings_t* s @@
                 ssd1306_drawstring("    TC Short to VCC", 1, 0);
             else
                 ssd1306_drawstring("#?, Unknown Error", 1, 0);
 			#endif
             ssd1306_drawstring("                    ", 2, 0);
             ssd1306_drawstring("-> to ignore all or", 2, 0);

max31865.c

➞

Show inline comments

@@ @@ -89,14 +89,17 @@ void max31865_readtemp(SPI_HandleTypeDef @@
         // Release CS
         HAL_GPIO_WritePin(MAX_CS, 1);
         status->error_code = data[0];
         HAL_Delay(400); // FIXME: remove?
         status->state_resume = status->state;
         status->state = STATE_TC_ERROR;
         status->temp = 0;
         status->temp_frac = 0;
         // check to see if it's an error we care about
         if(data[0] & 0b00111100) {
 			status->error_code = data[0];
 			status->state_resume = status->state;
 			status->state = STATE_TC_ERROR;
 			status->temp = 0;
 			status->temp_frac = 0;
+        }
         else {
         	max31865_clear_errors(spi_get());
+        }
+    }
     else
+    {
@@ @@ -107,7 +110,7 @@ void max31865_readtemp(SPI_HandleTypeDef @@
         	//convert adc to resistance
         	//Rrtd = adc / range * Rref
-        	status->temp = (int32_t) adc_count * 48600L;
+        	status->temp = (int32_t) adc_count * 40200L;
         	status->temp /= 32768L;
         	//resistance to temp
         	//(x - in1) * (cal2 - cal1) / (in2 - in1) + cal1
@@ @@ -127,7 +130,7 @@ void max31865_readtemp(SPI_HandleTypeDef @@
         	//convert adc to resistance
         	//Rrtd = adc / range * Rref
-        	status->temp = (int32_t) adc_count * 48600L;
+        	status->temp = (int32_t) adc_count * 40200L;
         	status->temp /= 32768L;
         	//resistance to temp
         	//(x - in1) * (cal2 - cal1) / (in2 - in1) + cal1

pid.c

➞

Show inline comments

@@ @@ -18,7 +18,7 @@ int16_t pid_update(therm_settings_t* set @@
   int32_t temp = (status->temp * 10) + temp_frac;
   // Calculate instantaneous error
-  int16_t error = status->setpoint * 10 - temp; // TODO: Use fixed point fraction
   int16_t error = status->setpoint * 10 - temp;
   // Proportional component
   int32_t p_term = set->val.k_p * error;

0 comments (0 inline, 0 general)