therm Changeset - e4fd36b0ba55 · protofusion repositories

Changeset - e4fd36b0ba55

Parent rev.

Child rev.

[Not reviewed]

cortex-f0

0 1 0

Ethan Zonca - 9 years ago 2015-06-05 21:12:37
ez@ethanzonca.com

Make error screen prettier

1 file changed with 3 insertions and 3 deletions:

display.c

0 comments (0 inline, 0 general)

display.c

➞

Show inline comments

@@ @@ -297,271 +297,271 @@ void display_process(therm_settings_t* s @@
             ssd1306_DrawString("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETUNITS;
+            }
             else if(!HAL_GPIO_ReadPin(SW_UP)) {
                 set->boottobrew = 1;
+            }
             else if(!HAL_GPIO_ReadPin(SW_DOWN)) {
                 set->boottobrew = 0;
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETUNITS:
+        {
             // Write text to OLED
             // [ therm :: set windup ]
             // [ g = 12         ]
             ssd1306_DrawString("Units: ", 0, 40);
             ssd1306_drawlogo();
             if(set->temp_units == TEMP_UNITS_FAHRENHEIT)
                 ssd1306_DrawString("Fahrenheit", 1, 60);
             else
                 ssd1306_DrawString("Celsius   ", 1, 60);
             ssd1306_DrawString("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_SETTEMPOFFSET;
+            }
             else if(!HAL_GPIO_ReadPin(SW_UP)) {
                 set->temp_units = TEMP_UNITS_FAHRENHEIT;
+            }
             else if(!HAL_GPIO_ReadPin(SW_DOWN)) {
                 set->temp_units = TEMP_UNITS_CELSIUS;
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_SETTEMPOFFSET:
+        {
             // Write text to OLED
             // [ therm :: set temp offset ]
             // [ g = 12         ]
             ssd1306_DrawString("Temp Cal Offset", 0, 40);
             ssd1306_drawlogo();
             char tempstr[6];
             itoa(set->temp_offset, tempstr, 10);
             ssd1306_DrawString("O=", 1, 45);
             ssd1306_DrawString("    ", 1, 57);
             ssd1306_DrawString(tempstr, 1, 57);
             ssd1306_DrawString("Press to accept", 3, 40);
             // Button handler
             if(SW_BTN_PRESSED) {
                 save_settings(&set);
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input_signed(&set->temp_offset);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_PREHEAT_BREW:
+        {
             // Write text to OLED
             // [ therm : preheating brew ]
             // [ 30 => 120 C             ]
             ssd1306_DrawString("Preheating...", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->setpoint_brew;
             // Button handler
             if(SW_BTN_PRESSED) {
 		save_setpoints(&set); // TODO: Check for mod
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input(&set->setpoint_brew);
+            }
             // Event Handler
             if(status->temp >= status->setpoint) {
                 status->state = STATE_MAINTAIN_BREW;
+            }
         } break;
         case STATE_MAINTAIN_BREW:
+        {
             // Write text to OLED
             // [ therm : ready to brew ]
             // [ 30 => 120 C           ]
             ssd1306_DrawString("Preheated!", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->setpoint_brew;
             // Button handler
             if(SW_BTN_PRESSED) {
 		save_setpoints(&set); // TODO: Check for mod
                 status->state = STATE_IDLE;
+            }
             else {
                 user_input(&set->setpoint_brew);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_PREHEAT_STEAM:
+        {
             // Write text to OLED
             // [ therm : preheating steam ]
             // [ 30 => 120 C           ]
             ssd1306_DrawString("Preheating...", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->setpoint_steam;
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
 		save_setpoints(&set); // TODO: Check for mod
+            }
             else {
                 user_input(&set->setpoint_steam);
+            }
             // Event Handler
             if(status->temp >= status->setpoint) {
                 status->state = STATE_MAINTAIN_STEAM;
+            }
         } break;
         case STATE_MAINTAIN_STEAM:
+        {
             // Write text to OLED
             // [ therm : ready to steam ]
             // [ 30 => 120 C            ]
             ssd1306_DrawString("Ready to Steam!", 0, 0);
             //ssd1306_drawlogo();
             draw_setpoint(status);
             status->pid_enabled = 1;
 	    status->setpoint = set->setpoint_steam;
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
 		save_setpoints(&set); // TODO: Check for mod
+            }
             else {
                 user_input(&set->setpoint_steam);
+            }
             // Event Handler
             // N/A
         } break;
         case STATE_TC_ERROR:
+        {
             // Write text to OLED
             // [ therm : ready to steam ]
             // [ 30 => 120 C            ]
             ssd1306_DrawString("Error:", 0, 0);
+            ssd1306_DrawString("Error:              ", 0, 0);
             if(status->tc_errno == 1)
-                ssd1306_DrawString("#1, Check Sensor", 1, 0);
+                ssd1306_DrawString("    Check Sensor (1)", 1, 0);
             else if(status->tc_errno == 4)
-                ssd1306_DrawString("#4, Check Sensor", 1, 0);
+                ssd1306_DrawString("    Check Sensor (2)", 1, 0);
             else
                 ssd1306_DrawString("#?, Unknown Error", 1, 0);
             ssd1306_DrawString("                    ", 2, 0);
             ssd1306_DrawString("Press -> to ignore", 3, 0);
             // Button handler
             if(SW_BTN_PRESSED) {
                 status->state = STATE_IDLE;
+            }
             else if(SW_RIGHT_PRESSED) {
                 set->ignore_tc_error = 1;
                 status->state = STATE_IDLE;
+            }
             // Event Handler
             // Maybe handle if TC is plugged in
             // N/A
         } break;
         // Something is terribly wrong
         default:
+        {
             status->state = STATE_IDLE;
             status->pid_enabled = 0;
         } break;
+    }
     if(last_state != status->state) {
         // Clear screen on state change
         goto_mode = 2;
         trigger_drawsetpoint = 1;
         ssd1306_clearscreen();
+    }
     // Last buttonpress
     sw_btn_last = sw_btn;
     sw_up_last = sw_up;
     sw_down_last = sw_down;
     sw_left_last = sw_left;
     sw_right_last = sw_right;
+}
 int32_t temp_last = 43002;
 int32_t setpoint_last = 10023;
 void draw_setpoint(therm_status_t* status) {
     // FIXME: need to do this when switching modes too
     if(status->temp != temp_last || trigger_drawsetpoint) {
         char tempstr[3];
         itoa_fp(status->temp, status->temp_frac, tempstr);
         ssd1306_DrawStringBig("      ", 3, 0);
         ssd1306_DrawStringBig(tempstr, 3, 0);
+    }
     if(trigger_drawsetpoint)
         ssd1306_DrawStringBig(">", 3, 74);
     if(status->setpoint != setpoint_last || trigger_drawsetpoint) {
         char tempstr[3];
         itoa(status->setpoint, tempstr, 10);
         ssd1306_DrawStringBig("   ", 3, 90);
         ssd1306_DrawStringBig(tempstr, 3, 90);
+    }
     trigger_drawsetpoint = 0;
     setpoint_last = status->setpoint;
     temp_last = status->temp;
+}
 // vim:softtabstop=4 shiftwidth=4 expandtab

0 comments (0 inline, 0 general)